MARS COMMERCE SOLO-KC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 34

MARS COMMERCE SOLO-KC Скачать руководство пользователя страница 6

SOLO-KC

INSTALLATION MANUAL

Page 6

5

LED DISPLAY

BLUE LED (LED1)

-

Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak signal, 5 is
excellent signal)

RED LED (LED2)

-

When LED 2 is ON the unit has a problem with a GSM network connection or the GSM
part of the unit is out of order. In this case immediately call the service!

YELLOW LED (LED3)

-

Short flashing indicates that the GSM module is ON, but it is not yet connected on the GSM
network. After connection, Yellow LED is flashing with short pulse ON and a long pulse
OFF.

6

CLEAR ALL PROGRAMMED DATA FROM SIM

This is highly recommended when a SIM card you are going to use for the SOLO-KC is not new
and it already has some data stored in the phone book memory.

By sending this SMS to SOLO-KC all programmed parameters and numbers are cleared:

;SDCLR;

After sending SMS you should wait at least 60 second for the command to be executed!

NOTE

By sending this command to the SOLO-KC all programmed data are erased from the
SIM card, including SMS messages! After the device will start it will be configured
with factory defaults.

«
...
4
5
6
7
8
...
»

Содержание SOLO-KC



































Отзывы:

Нет отзывов