Marport Trawl Explorer Скачать руководство пользователя страница 11

Страница: 11 / 94

Trawl Explorer | V5 | Introduction and Presentation

Beamwidth

Beamwidths for uplink pings:

Beamwidth

@ 35 kHz

@ 50 kHz

@ 60 kHz

-3dB

46°

40°

30°

Beamwidths for up and down pings:

Beamwidth

@ 125 kHz

@ 160 kHz

@ 200 kHz

-3dB

26°

24°

22°

Outline dimensions

146 mm

500 mm

400 mm

Main Parts

External View

Retainer screw

Model/serial

number

Metal strap

Transducer

Stabilizer board

Pressure sensor

Temperature sensor

Positive charge

Negative charge

10.

Water switch

11.

Shoulder bolts

The serial number may also be written on a plate on the side of the housing.

CAUTION:

• Do not put foreign objects into depth sensor opening or try to open it.
• Do not remove the shoulder bolts from the outside of the sensor

It may damage the components.

Содержание Trawl Explorer































































































Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды

Marport Trawl Explorer, Руководство по обслуживанию

Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды