Marport Trawl Explorer страница 10 Скачать руководство пользователя

Страница: 10 / 94

Trawl Explorer | V5 | Introduction and Presentation

Description

Firmware

There are three versions of the Trawl Explorer. Each version has a different firmware (called NBTE)
and different features.

NBTE V1

NBTE V2

NBTE V3

Name of firmware

FIRM121

FIRM126

FIRM128

Autorange feature

yes

Target strength on echograms

yes

Technical Specifications

Uplink frequency

30 to 60 kHz

Range to vessel

up to 2500 m*

Sounder broadband frequency

Configurable between 120-210 kHz

Sounder range

V1/V2 5 to 80 m - V3 5 to 160 m

Data update rate

Depth: 1-8 sec. - Temp/Battery/Height/Pitch&Roll:
every 6 sec.

Echogram update rate

V1 up to 1 image/second - V2/V3 up to 3 images/second

Pitch angle

±90°

Roll angle

V1 ±90°; V2, V3 ±180°

Pitch & roll accuracy

±0.1°

Depth resolution

0.1m with 0.1% accuracy

Temp measurement range

-5° C to +25° C

Temp accuracy

±0.1° C

Battery type

Lithium-Ion

Typical battery life:

30-75 hours †

Standard: 8-12 hours ‡

Charging time

Fast Charge: 4 hours

Weight in air (with housing)

16 kg

Weight In water (with housing)

4.1 kg

Warranty

2 years (Sensor & Battery)**

*Reference only. Depends on functions enabled. / † Depends on sensor uplink power. / ‡ Based on
average charging time. / **Marport Standard Marine Limited Warranty

Содержание Trawl Explorer































































































Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды

Marport Trawl Explorer, Руководство по обслуживанию

Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды