Marine Power Solutions MP-4120Ti Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 23

background image

5

2.5 Preparation Before Starting

Before starting engine make sure that:

There is no

FUEL LEAKAGE

There is no

WATER LEAKAGE

There is no

OIL LEAKAGE

There is no

SMELL OF LP-GAS

in the deep cavities of the boat or elsewhere

The

OIL LEVELS

are correct

The

COOLING WATER LEVEL

in the expansion tank for the fresh water system is correct.

The proper

NAUTICAL CHARTS

are on board for the planed voyage

There is enough FUEL on board for the planed voyage
Make sure when filling your fuel tank that there is no open flame on board. Ventilate the boat and

run the engine room fan (if fitted) for 4 minutes before starting the engine. Do not overfill fuel tank.

3.

Engine Component Guide

1.  AIR FILTER
2.  FUEL FILTER
3.  EXPANSION TANK
4.  OIL SUMP PUMP
5.  SEA WATER PUMP
6.  OIL PRESSURE SENSOR
7.  START MOTOR
8.  SOLENOID

«
...
3
4
5
6
7
...
»

Содержание MP-4120Ti
























Отзывы:

Нет отзывов

Похожие инструкции для MP-4120Ti

Pad-Mounted Series

Бренд: S&C Страницы: 15

Бренд: Vanguard Страницы: 120

Бренд: RCGF Страницы: 22

Бренд: Saito Страницы: 2

Бренд: Bodine Страницы: 8

Бренд: Mercedes-Benz Страницы: 324

Бренд: EX Model Engines Страницы: 2

Бренд: Nederman Страницы: 44

Бренд: Beta Страницы: 76

Бренд: Saito Страницы: 5

Бренд: Saito Страницы: 6

Бренд: Yanmar Страницы: 308

Бренд: Yanmar Страницы: 316

Бренд: Pratt & Whitney Страницы: 576

Бренд: Kyosho Страницы: 8

Бренд: Wood-mizer Страницы: 226

Бренд: pro.point Страницы: 64

Бренд: Hobbico Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды