45
46
8. ALIGNMENT PROCEDURES
TUNER
1. Equipment Requried
- AM Standard Signal Generator (AM SSG)
- Audio Generator
- Oscilloscope
- Distortion Meter
- AC Voltmeter
- DC Voltmeter
- FM Standard Signal Generator (FM SSG)
- Frequency Counter
- Stereo Modulator
Note : Disconnect external FM antenna prior to alignment.
2. Alignment.
2-1. Alignment Test Point
Step
Subject
Signal
generator
setting
Set
frequency
setting
Equipment
connection
Adjustment
point
Adjust for
1
Tunning
voltage
522kHz
522kHz
DC voltmeter
RF BLOCK
OSC coil
522 kHz : 1.0 ~ 1.3V
1611 kHz : 7.0 ~ 8.5V
2
IF Tracking
603kHz
603kHz
IF BLOCK
Coil
KSNT-111I
Maximize audio output
3
RF Tracking
603kHz
603kHz
AC voltmeter
oscilloscope
tape monitor
L/R
AC voltmeter
oscilloscope
tape monitor
L/R
AC voltmeter
oscilloscope
tape monitor
L/R
RF BLOCK
ANT coil
Maximize audio output
Repeat LOW, HIGH
frequency
4
Seek level
999kHz
999kHz
(K,N)
(K,N)
(K,N)
(K,N)
(K,N)
(K,N)
(K,N)
(K,N)
520kHz
(U)
520kHz
(U)
600kHz
(U)
600kHz
(U)
600kHz
(U)
600kHz
(U)
1000kHz
(U)
1000kHz
(U)
SVR 03
Tuned on point
Step
Subject
Signal
generator
setting
Set
frequency
setting
Equipment
connection
Adjustment
point
Adjust for
1
Tunning
voltage
152kHz
152kHz
DC voltmeter
RF BLOCK
OSC coil
522 kHz : 1.5 ~ 2.3V
1611 kHz : 6.0 ~ 7.5V
2
RF Tracking
162kHz
162kHz
AC voltmeter
oscilloscope
tape monitor
L/R
AC voltmeter
oscilloscope
tape monitor
L/R
RF BLOCK
ANT coil
Maximize audio output
Repeat LOW, HIGH
frequency
3
Seek level
207kHz
207kHz
Tuned on point
2-2. AM(MW) Alignment
Output of signal generator should not be greater than necessary to obtain an optimum output reading.
Signal generator modulation ................................................................. 30%
Signal frequency ................................................................................ 400Hz
Modulation frequency ........................................... 603, 999, 1404kHz (K,N)
Modulation frequency ............................................ 600, 1000, 1400kHz (U)
Switch ........................................................... press the BAND Button to AM
2-3. LW Alignment (N Version only)
Output of signal generator should not be greater than necessary to obtain an optimum output reading.
Signal generator modulation ................................................................. 30%
Signal frequency ................................................................................ 400Hz
Modulation frequency ....................................................... 162, 207, 252kHz
Switch ........................................................... press the BAND Button to LW
Содержание SR7200
