Marantz SR5600, Руководство по обслуживанию

Страница: 40 / 101

56
IC35: CS5361
I
I
I
I
I
I
I
I
O
I
I
I
I
I
I
I
I
I
I
I
O
I
O
I/O
RST 1 24 FILT+
M/S 2 23 REFGND
LRCK
3 22
VCOM
SCLK 4 21 AINR +
MCLK 5 20 AINR -
VD 6 19 VA
GND 7 18 GND
VL
8 17
AINL-
SDOUT 9 16 AINL+
DIV 10 15 TST
HPF
11 14
M1
DIF 12 13 M0
Pin Name # Pin Description
RST 1 Reset ( Input ) - The device enters a low power mode when low.
M/S
2
Master/Slave Mode (Input ) -In Slave mode, LRCK and SCLK become input. (FIXED LOW)
LRCK 3 Left Right Clock ( Input ) - Determines which channel, Left or Right, is currently active on the
serial audio data line. The frequency of the left/right clock must be at the audio sample rate, Fs.
SCLK 4 Serial Clock ( Input ) - Serial clock for the serial audio interface.
MCLK 5 Master Clock ( Input ) - Clock source for the delta-sigma modulator and digital filters. Table 1 illustrates
several standard audio sample rates and the required master clock frequency.
VD 6
Digital Power ( Input ) - Positive power supply for the digital section. Refer to the Recommended Operat-
ing Conditions for appropriate voltages.
GND 7,18 Ground ( Input ) - Ground reference. Must be connected to analog ground.
VL 8 Logic Power ( Input ) - Determines the required signal level for the digital input/output. Refer to the Rec-
ommended Operating Conditions for appropriate voltages.
SDOUT 9 Serial Audio Data Output ( Output ) - Output for two’s complement serial audio data.
DIV 10 MCLK Divider (Input ) - (FIXED LOW)
HPF
11
High Pass Filter Enable (Input ) -
The device includes a high pass filter after the decimator to remove
the indeterminate DC offsets introduced by the analog buffer stage and the analog modulator. The first-
order high pass filter response characteristics are detailed in the Digital Filter specifications table. The fil-
ter response scales linearly with sample rate.
DIF 12 Digital Interface Format ( Input ) - The required relationship between the Left/Right clock, serial clock
and serial data is defined by the Digital Interface Format selection. Refer to Figures 8 and 9.
M0
M1 13,
14
Mode Selection ( Input ) - (FIXED LOW)
TST 15 Test Pin (Input) - This pin needs to be connected to GND.
AINL+
AINL-
16,
17
Differential Left Channel Analog Input ( Input ) - Signals are presented differentially to the delta-sigma
modulators via the AINL+/- pins. The full scale differential analog input level is specified in the Analog
Characteristics Specification table.
(FIXED LOW)
VA 19
Analog Power ( Input ) - Positive power supply for the analog section. Refer to the Recommended Oper-
ating Conditions for appropriate voltages.
AINR+
AINR- 20,
21
Differential Right Channel Analog Input ( Input ) -Signals are presented differentially to the delta-sigma
modulators via the AINR+/- pins. The full scale differential analog input level is specified in the Analog
Characteristics Specification table.
VCOM 22 Common Mode Voltage (Output) -
Nominally 2.5 volts; can be used to bias the analog input circuitry to
the common mode voltage of the CS5361. VCOM is not buffered and the maximum current is 10 uA.
REF_GND 23 Reference Ground ( Input ) - Ground reference for the internal sampling circuits and must be connected
to analog ground.
FILT+ 24 Positive Voltage Reference ( Output ) - Positive reference voltage for the internal sampling circuits.
Requires the capacitive decoupling to GND as shown in the Typical Connection Diagram.
Volta ge R e fe ren ce
S e rial O utpu t Interfa ce
D igital
F ilte r
H ig h
P a ss
F ilter
H ig h
P a ss
F ilter
D e cim ation
D igital
F ilte r
D e cim ation
D A C
-
+
S /H
D A C
-
+
S /H
A IN R +
S C L K
S D O U T M C LK
R S T
V C O M L R C K
A IN R -
A IN L+
A IN L-
F ILT +
D IF
M /S
H P F
M O D E 0
M O D E 1
R E F G N D
V
L
D IV
Q LP Filter
Q LP F ilter