MAQ SONAR 22KHz страница 65 Скачать руководство пользователя

Страница: 65 / 107

System

Setup

Transducer Alignment

The transducer alignment may require alteration as the transducer serviced or when a

replacement transducer is installed.

Tsh

Transducer Shield

OFF

Stainless Steel transducer shield removed or

60/90 kHz ABS shield installed.

Stainless Steel shield installed.

Note that if the transducer shield is removed or replaced the Frequency Adjust

(below)

calibration must be conﬁrmed.

While stationary in port, switch to OMNI mode and adjust the Range, Gain, Near Gain and

Far Gain controls

(on the Operate panel)

to obtain a stable target on the display of

medium strength. Choose a ﬁxed position target such as the shoreline or a standing
vessel.

Switch to the System Panel and vary the Frequency Adjust to ensure maximum

target

strength.

DO NOT

attempt to adjust the Frequency while the vessel is underway.

Frequency Adjust

Tuning the transducer is similar to checking the resonance of bell or tuning

fork.

Resonance can vary from transducer to transducer and can change slightly

as the

transducer ages. The transducer frequency must be tuned for maximum

performance.

Содержание 22KHz












































































































Результаты поиска

Содержание 22KHz

Отзывы:

Похожие инструкции для 22KHz

Бренды по названию

Популярные бренды

MAQ SONAR 22KHz, Техническое и монтажное руководство

Результаты поиска

Содержание 22KHz

Отзывы:

Похожие инструкции для 22KHz

Бренды по названию

Популярные бренды