manualshive.com logo in svg

Mantis SV-5C/2, Руководство пользователя, Страница: 7 / 20

Поделиться
Скачать
Mantis SV-5C/2 Скачать руководство пользователя страница 7

7

ASSEMBLY 

(continued)

WARNING • DANGER

FUEL IS EXTREMELY FLAMMABLE.

HANDLE IT WITH CARE. KEEP AWAY
FROM IGNITION SOURCES. DO  NOT

SMOKE WHILE FUELING YOUR

EQUIPMENT.

Mixing Fuel

Your MANTIS Tiller is powered by a

commercial two stroke, air cooled engine
which requires a fuel mixture of gasoline
and lubricating oil.

Use a mixture of 50 parts unleaded

regular gasoline and 1 part two-stroke 
MANTIS oil (50:1.) Use branded 89 octane
(R+M+2) unleaded gasoline or gasohol
(maximum 10% ethyl alcohol, or 15% MTBE, no methyl alcohol.) 

!

1 gallon

2.6 oz. bottle of 

MANTIS 50:1 2-cycle engine oil

Never use starting fluids as they will cause permanent engine
damage. Using them will void the warranty. Before you use the
tiller, read the Safety & Warning rules on pages 3-4.

WARNING

AVOID ACCIDENTAL BLADE ENGAGEMENT

DO NOT SQUEEZE THE THROTTLE 

TRIGGER WHEN STARTING.

MAINTAIN PROPER IDLE SPEED ADJUSTMENT 

(2500-3100 RPM)

!

!

Picture 1

Picture 2

Picture 3

Picture 4

Picture 5

STARTING

To Start Your Tiller for the
First Time:

1. Fill the fuel tank with the proper

oil/gasoline mixture. 
(See previous section.)

2. Hand tighten the gasoline cap just

until it’s snug.

3. Place the 

o/

I

switch into the 

I

“start/on” position. (Picture 1)

4. Pull the choke button all the way

out, to completely close the choke.
(Picture 2)

5. Locate the 

purge bulb

on the

upper right of the engine, in front of
the fuel tank. 

(See Picture 3)

It sends

fuel into the carburetor, 

for easy

starting.

Press the 

purge bulb

until

you see fuel flow through the 

clear fuel

return line

. Since you’re starting

“cold,” you may need to press six to
eight times. As soon as fuel starts
flowing through the clear fuel line, stop
pressing! (Picture 3)

6. 

Don’t

press the throttle trigger

during the starting of the engine.

7. Pull the starter cord (Picture 4)

until resistance is felt. Then give the
recoil starter cord a few brisk pulls until
the engine 

fires.

Note: Pull the starter

cord about 12" to 18". 

During cold start-

ing,

you may need to pull at least three or

four times before the engine

fires.

NOTE: When the choke is closed,
never pull the cord more than four or

five times. Overpulling may cause
flooding. Also, bear in mind that, when
the engine 

fires, it only coughs or

sputters, and will not run on choke.

8. Push the choke button in, all the

way, to open the choke. (Picture 5)

9. Then pull the starter cord again.

The engine should start and run. Let the
engine warm up two to three minutes
before using.

Follow these steps whenever you are
starting the engine “cold”, or when the
engine has run dry and you have just
added fuel. Remember, always use short,
brisk pulls. Don’t give the cord a long,
forceful yank. 

And, do not let the cord

snap back into the starter housing.

Starting a 
Warm Engine

1. Push ignition switch to 

I

“start/on” position.

2. Push choke button in to

the RUN (open) position.

3. If there is no fuel in the

clear return line, push primer
bulb 3-4 times or until fuel is
visible in the line.

4. Pull starter rope using

short pulls, 1/2 to 2/3 of the
rope length.

5. If engine fails to start in 4

pulls, use “First Time” starting
procedure on page this page.

6. With engine running, and

both hands on the handles, 
press the throttle lock out
button (Picture 1), then squeeze
the throttle trigger gradually to
increase the engine speed and
engage the tines.

NOTE:

Once the throttle

trigger is squeezed, you can
release the lockout button
(Picture 2). 

NOTE:

Step #6 must be

repeated each time your tiller
trigger is released.

Picture 1

Picture 2

Содержание SV-5C/2





















Отзывы:

Нет отзывов