background image

symptoms

Possible causes

Solutions

The learning cycle does not start. 
The LED blink 4 times

The battery pack is empty

Wait 6 to 8 hours before using the 
shutter.

The learning cycle does not start. 
The LED is ON

The order is defective

Verify that protective cover of the 
battery is removedVerify that the 
battery is not defective (the LED is ON
while pushing)

The learning cycle does not start
The LED is OFF

The order is defective

Verify that protective cover of the 
battery is removedVerify that the 
battery is not defective (the LED is ON
while pushing)

The motor is not powered

Verify the plug between the control 
box and the power supply Verify the 
power supply connection

The opening button make the
shutter closing

The order is inverted

Proceed to the reversal of the functions 
of the transmitter buttons 
(see programming instructions)

The closing button make the
shutter opening

The order is inverted

Proceed to the reversal of the functions 
of the transmitter buttons 
(see programming instructions)

The shutter does not start when there 
is an opening or closing order

The order is defective

Verify that the battery is not defective 
(the LED is ON while pushing)

The battery pack is empty

Verify the electrical wire plug : Wait 6 
to 8 hours before using the shutter.

The shutter does not close completely

There is an obstacle or bad learning

Remove the obstacle and/or do a 
learning cycle again

The battery pack is empty

Verify the electrical wire plug : Wait 6 
to 8 hours before using the shutter.

The shutter does not close completely

There is an obstacle or bad learning

Remove the obstacle and/or do a 
learning cycle again

The battery pack is empty

Verify the electrical wire plug : Wait 6 
to 8 hours before using the shutter.

The shutter is hardly closing

Bad learning

Do a learning cycle again

The shutter is hardly opening

Bad learning

Do a learning cycle again

The drive is noisy (popping noise)

Belt relaxed

Tighten the belt

DIAGNOSTIC HELP

Reversal of the functions of the transmitter buttons

This operation is necessary in case where the shutters open by pressing the (>< ) button of the transmitter.
Position the shutters near the ‘close’ position (approx. 10 to 15 cm). In this new position, start again the operation Learning mode 
and saving.

NM V323

A

09-2014

MANTION SAS 

- 25000 Besançon - Tel +33 3 81 50 56 77 - Fax +33 3 81 85 38 79 - www.mantion.com

20/20

Содержание SLIDSOFT NM V323





















Отзывы: