Manitowoc S600M Скачать руководство пользователя страница 65

Страница: 65 / 103

Section 6

Electrical System

Part Number 80-1630-3

6-25

Diagnosing An Ice Machine That Will Not Run

Warning

High (line) voltage is applied to the control board
(terminals #55 and #56) at all times. Removing
control board fuse or moving the toggle switch to
OFF will not remove the power supplied to the
control board.

Step

Check

Notes

Verify primary voltage supply to ice
machine.

Verify that the fuse or circuit breaker is closed.

Verify the high-pressure cutout is closed.

The H.P.C.O. is closed if primary power voltage is present at terminals
#55 and #56 on the control board.

Verify control board fuse is OK.

If the bin switch light functions, the fuse is OK.

Verify the bin switch functions properly.

A defective bin switch can falsely indicate a full bin of ice.

Verify ICE/OFF/CLEAN toggle switch
functions properly.

A defective toggle switch may keep the ice machine in the OFF mode.

Verify low DC voltage is properly
grounded.

Loose DC wire connections may intermittently stop the ice machine.

Replace the control board.

Be sure Steps 1-6 were followed thoroughly. Intermittent problems are
not usually related to the control board.

Содержание S600M








































































































Результаты поиска

Содержание S600M

Отзывы:

Похожие инструкции для S600M

Бренды по названию

Популярные бренды

Manitowoc S600M, Руководство по обслуживанию

Результаты поиска

Содержание S600M

Отзывы:

Похожие инструкции для S600M

Бренды по названию

Популярные бренды