manualshive.com logo in svg

Manitowoc Cleveland KET-12-T, Руководство оператора, Страница: 4 / 10

Поделиться
Скачать
Manitowoc Cleveland KET-12-T Скачать руководство пользователя страница 4

GENERAL

Installation of the kettle must be accomplished by
qualified electrical installation personnel working to all
applicable local and national codes. Improper installation
of product could cause injury or damage.

This equipment is built to comply with applicable
standards for manufacturers. Included among those
approval agencies are: UL, NSF, ASME/Ntl. Bd., CSA,
CGA, ETL, and others. Many local codes exist, and it is
the responsibility of the owner/installer to comply with
these codes.

RECEIVING INSPECTION

Before unpacking visually inspect the unit for evidence of
damage during shipping.

If damage is noticed, do not unpack the unit, follow
Shipping Damage Instructions shown below. 

SHIPPING DAMAGE INSTRUCTIONS

If shipping damage to the unit is discovered or
suspected, observe the following guidelines in preparing
a shipping damage claim. 

1. Write down a description of the damage or the reason

for suspecting damage as soon as it is discovered.
This will help in filling out the claim forms later.

2. As soon as damage is discovered or suspected, notify

the carrier that delivered the shipment.

3. Arrange for the carrier's representative to examine the

damage.

4. Fill out all carrier claims forms and have the examining

carrier sign and date each form.

UNCRATING

Caution

:

Straps under tension and will snap when cut.

Carton may contain staples and Skid contains Nails.

Use proper safety equipment and precautions.

Unit is heavy use adequate help or lifting equipment as
needed.

INSTALLATION

M

Mo

od

de

ell  //  S

Se

erriia

all #

#

1x 6

3.

1.

Carefully cut any straps from container.

2.

Lift off carton.

3.

Inspect for hidden damage. If found refer to
“SHIPPING DAMAGE INSTRUCTIONS”.

4.

Cut strap holding unit.

5.

Remove 1X6  holding unit in place.

6.

Remove manual from kettle pot. Write down the model
# and serial# of the unit onto the front of this manual.

7.

Lift kettle off skid and move kettle to its installation
location.

8.

Discard packaging material according to local and or
state requirements.

Model #

Unit

Unit with 

shipping box

KET3T

55 lbs.

95 lbs.

KET6T/GB

130 lbs.

170 lbs.

KET12T/GB

150 lbs.

190 lbs.

KET20T

220 lbs.

260 lbs.

TKET3T

95 lbs.

135 lbs.

TKET6T

186 lbs.

226 lbs.

TKET12T

275 lbs.

315 lbs.

APPROXIMATE WEIGHTS

Содержание Cleveland KET-12-T











Отзывы:

Нет отзывов