Manitowoc AUCS Q Скачать руководство пользователя страница 5

 

 

 

Section 1

 

General Information

1-1 

Section 1 

General Information 

 

Freight Damage and Claims 

Procedures 

1. Shortages 

Check the number of cartons delivered against the 
quantity shown on your receipt. If the quantities 
do not match, have the driver note the shortage 
and file your claim with the freight company. 

2.  No-Fault Claim Procedure 

Manitowoc assumes responsibility for all freight 
damage claims involving participating carriers, 
with the following exceptions: 

• 

When the trucking company loses the 
equipment. 

• 

When fire destroys the equipment en route. 

• 

When a traffic accident damages the shipment 
en route. 

3. Visible 

Damage 

A.  If a carton appears damaged in any way, open 

the carton and inspect the contents in the 
presence of the driver. Note the nature and 
extent of the damage on the freight bill. 

B.  Notify your local Manitowoc distributor to 

inspect the merchandise within 15 days of 
delivery. Do not attempt to repair the damage. 

4. Concealed 

Damage 

A.  If damage is noticed at the time of 

installation, notify the distributor immediately 
and ask for an inspection. 

B.  Do not destroy packing materials until the 

inspection is completed. 

These conditions must be met before your claim 
can be processed by the distributor. 

5. Claims 

Manitowoc Ice, Inc. and your local distributor 
will arrange to repair or replace the equipment. 

Model/Serial Number Location 

Record the model and serial number of the AuCS

®

accessory in the space provided below. These 
numbers are required when requesting information 
from your local Manitowoc distributor, service 
representative, or Manitowoc Ice, Inc. 

The model and serial number are listed on the 
OWNER WARRANTY REGISTRATION CARD. 
They are also listed on the MODEL/SERIAL 
NUMBER DECAL affixed to the side of the 
AuCS

®

A accessory. 

 

MODEL AND 

SERIAL NUMBER 

PLATE

SV1275

 

Model/Serial Number Location 

 

 Ice 

Machine 

Bin/Dispenser 

Model Number 

 

 

Serial Number 

 

 

 Remote 

Condenser or 

Condensing Unit 

AuCS

®

Accessory 

Model Number 

 

 

Serial Number 

 

 

 

Содержание AUCS Q





























Отзывы: