Manitou MC 25-2 D K ST3A S1 Скачать руководство пользователя страница 78

Страница: 78 / 102

REPLACE

Hydraulic return oil filter cartridge

IMPORTANT

Do not operate the lift truck without the cartridge in place, as this would immediately damage the hydraulic

transmission system, the pump and the hydrostatic wheel motors.

- Stop the engine on level ground.

- Release the pressure from the circuits by operating the hydraulic controls.

- Open the engine cover (

2 - DESCRIPTION: CONTROL AND COMMAND

INSTRUMENTS).

- Carefully clean the outside of the filter and the area surrounding it

- Unscrew the plug 1 with a wrench.

- Remove the hydraulic oil filter cartridge 2 from the filter head 3 and replace it with

a new one (

MAINTENANCE: FILTERS CARTRIDGES AND BELTS).

- Refit the unit.

- Check the hydraulic oil level (

MAINTENANCE: 50H - WEEKLY MAINTENANCE).

REPLACE

Alternator

belt

IMPORTANT

If the alternator belt has to be changed, check the tension again after the first 20 hours of operation.

- Open the engine cover (

2 - DESCRIPTION: CONTROL AND COMMAND

INSTRUMENTS).

- Remove the cover plate 1.

REMOVING THE BELT

- Loosen screws 2 by two to three turns.

- Swivel the alternator assembly so as to remove alternator belt 3.

NOTE: Take advantage of belt removal to check the correct operation of the pulleys

and bearings (noise, rubbing, play, etc.).

REFITTING THE BELT

- Refit a new alternator belt (

FILTERS CARTRIDGES AND BELTS). and ensure that

it is properly seated in the grooves of each pulley.

- Adjust the belt tension between the crankshaft and alternator pulleys.

- Under pressure applied by the thumb (98 N), belt movement A should be between

7 and 9 mm.

- Retighten screws 2 (tightening torque 22 N.m).

3 - 22

647635 (12/12/2017) MC 18-2 / MC 18-4 ST3A S1

www.

duma

-rent.com

Содержание MC 25-2 D K ST3A S1







































































































Результаты поиска

Содержание MC 25-2 D K ST3A S1

Отзывы:

Бренды по названию

Популярные бренды

Manitou MC 25-2 D K ST3A S1, Руководство оператора

Результаты поиска

Содержание MC 25-2 D K ST3A S1

Отзывы:

Бренды по названию

Популярные бренды