Manitou MARA PIGGYBACK Скачать руководство пользователя страница 3

Страница: 3 / 41

MARA PIGGYBACK SERVICE MANUAL

This manual is intended to provide the information necessary for the

250 hour full service of the Manitou Mara PiggyBack shock. We highly

recommend installation and service be performed by a qualified mechanic.

These instructions can be downloaded from the Hayes Performance Systems

website at www.manitoumtb.com

INTRODUCTION

We highly recommend that service to this shock be performed by a certified

bicycle mechanic. Failure to follow instructions presented in this manual

could lead to serious injury or death. Any questions about the servicing

of this shock or the manual itself should be directed to Hayes Customer

Support at:

Phone: 888-686-3472

Email: [email protected]

Suspension shocks by design can contain preload springs, gases and fluids

under extreme pressures.Warnings contained in this manual must be

observed to avoid damage to shock,serious injury or even death.

WARNING

Содержание MARA PIGGYBACK










































Результаты поиска

Содержание MARA PIGGYBACK

Отзывы:

Похожие инструкции для MARA PIGGYBACK

Бренды по названию

Популярные бренды

Manitou MARA PIGGYBACK, Руководство по обслуживанию

Результаты поиска

Содержание MARA PIGGYBACK

Отзывы:

Похожие инструкции для MARA PIGGYBACK

Бренды по названию

Популярные бренды