background image

Page 2 

Introduction 

WaveGuide ceiling and in-wall speakers are 

 

designed  to provide clear, sharply-focused audio  
reproduction while remaining unobtrusive in the 

 

background. These speakers bring out the best in any 
home theater or whole-house stereo system. These 
products also offer many features, including: 

1” Asymmetrical  Aluminum Dome Tweeter 

Slide switches for bass and treble control  
(+/-3dB) 

Cam-lock mounting system with isolated 

 

rubber pads to reduce vibration 

Kevlar cone for low distortion and smooth  
response 

Molded in IR lens that allows installation of an  
infra-red receiver through the speaker baffle 

Gasket around the baffle to provide an  
acoustic seal 

 

Description 

 

Ceiling Speakers  

(Sold in Pairs)

 

           

WG100C

 

Page 2 

Frequency Response 

50Hz to 20kHz (+/-3db) 

Maximum Power Rating 

100 Watts 

Impedance Rating 

8-Ohms 

Overall Speaker Dimension  9” Diameter 

Specifications 

6” Kevlar cone woofer;  
1” asymmetrical aluminum dome 
tweeter 

Mounting Dimension w/o 
Mounting Ring 

7 1/2” Diameter 

Mounting Ring Dimension 

8 3/16” Diameter 

Grille  

Aluminum 

Color 

White 

TM 

Page 23 

WARRANTY 

M&S Systems

 Limited 10-Year Warranty for WaveGuide

 

Speakers and AirVac

 Gold Power Units 

M&S Systems offers a 10-Year Warranty on our WaveGuide™  
speakers and  AirVac™ Gold power units.  This warranty is identical 
to the M&S Systems™ 2-Year Warranty, with the exception that this 
warranty covers the  WaveGuide™ speakers and AirVac™ Gold 
power units for 10 years instead of 2.  The M&S Systems™ 10-Year 
Warranty applies ONLY to the  WaveGuide™ speakers and   
AirVac™ Gold power units and to no other M&S Systems™, M&S™ 
8- ohm or AirVac™ products.    
 

M&S Systems Limited 2-Year Warranty 

M&S Systems warrants its products to be free of defects for 2 years. 
Except for the WaveGuide™ Speakers and  AirVac™ Gold power 
units (See above). The warranty period begins on either (a) the date 
of purchase or installation date of this product or (b) the date of  
closing on a new residence in which this product was originally  
installed.  
The warranty extends to the original user of the product and to each 
subsequent owner of the product during the term of the warranty. 
M&S™ will repair or replace, at its option, parts and materials at no 
charge. Parts supplied under this warranty may be new or rebuilt at 
the option of M&S Systems™. 
If during the warranty period the product appears to have a defect, 
please call our toll free service  number (800-366-9422) prior to  
dismantling. Dismantling the product prior to calling our service  
number may void the warranty. Before returning any product to M&S 
Systems™, obtain a Return Authorization Number (RAN) from our 
service department. M&S Systems will return the repaired 

 

product freight prepaid within the continental United States.  ANY 
PRODUCT RETURNED TO M&S SYSTEMS WITHOUT A RAN 
NUMBER WILL BE REFUSED. 
This limited warranty is in lieu of any other warranties, express or 
implied, including any implied warranty of merchantability or fitness 
for a particular purpose or otherwise, and of any other obligations or 
liability on the seller’s part.  This limited warranty does not cover 
damage caused by improper installation, acts of God, criminal acts, 
the violation of applicable building or electrical codes or the use of 
non-M&S wire, cable (excluding CAT5 and RG-6) or wall housings. 
Under no circumstances shall M&S Systems™ be liable for  
consequential, incidental or special damages arising in connection 
with use, or inability to use this product.  In no event shall M&S  
Systems™ liability hereunder exceed the cost of the product  
covered hereby.  No person is authorized to assume for us or  
obligate us for any other liability in connection with the sale of this 
product. Some states do not allow the exclusion or limitation of  
consequential, incidental or special damages, so the above 

 

limitation or exclusion may not apply to you.  This limited warranty 
gives you specific legal rights, and you may also have other rights, 
which vary from state to state. 

TM 

Содержание WaveGuide WG100C













Отзывы: