Mancorp Powerjet PJE Series, Руководство оператора

Страница: 9 / 22

WARNING: High pressure
spray can cause paint chips or
other particles to become
airborne and fly at high speeds.
To avoid personal injury, eye
safety devices must be worn.
6. Eye safety devices and foot
protection must be worn when
using this equipment.
7. High pressure developed by these units will cause
personal injury or equipment damage. Use caution
when operating. Do not direct discharge stream at
people, or severe injury or death will result.
8. Never make adjustments on machine while in
operation.
9. Units with shut-off gun should not be operated
with the gun in the off position for extensive periods
of time as this may cause damage to the pump.
10. The best insurance against an accident is
precaution and knowledge of the machine.
11. Mancorp will not be liable for any changes made
to our standard units, or any components not
purchased from Mancorp.
12. Read engine safety instructions provided.
WARNING: Keep water spray
away from electric wiring or fatal
electric shock may result.
13. Never run pump dry or leave
gun closed longer than 5 minutes.
14. Do not allow children to
operate the pressure washer at any
PRE-OPERATION CHECK
* Pump oil (SAE 30W no-detergent oil, General)
* Cold water supply (6 GPM-5/8”-20 PSI)
* Hose, wand, nozzle
* Water filter (intact, non restrictive)
* Fuel (unleaded 86 or higher octane)
* Engine oil (SAE 10W30)
SET-UP PROCEDURES
1. Attach a 5/8” garden hose to inlet connector.
minimum flow should be 5 gpm.
2. Attach high pressure hose to discharge nipple
using quick coupler. Lock coupler securely into place
by pulling back coupler collar and inserting it onto
discharge nipple, then pushing collar forward to lock
in place.
3. Attach wand to spray gun using teflon tape on
threads to prevent leakage.
4. Attach swivel connector on discharge hose to
spray gun using teflon tape on threads.
5. Remove oil plug on top of pressure washer pump
and replace with dipstick supplied. (This may be
installed from the factory.)
6. Check oil level on sight glass on side of pump.
Oil
should be visible one half way up sight glass ( 30W
non-detergent).
7. Fill gasoline tank and check engine oil.
8. Electric start models require a 12V U-1 garden
tractor battery (not included).
OPERATING INSTRUCTIONS
1. Read engine warning and operating instructions.
2. Turn on water at faucet and pull trigger on spray
gun allowing water to flow until all air has
discharged from system. Check for water leaks;
tighten as needed.
3. Pull wand coupler collar back and insert pressure
nozzle into coupler then secure by pushing collar
forward.
4. Read engine manual, turn on gas valve, choke,
turn switch to start position and pull rope to start.
( On electric start engines turn the engine switch to
the start position and hold it there until engine starts.
Note: Do not use the electric starter more than 5
seconds at a time.
When engine starts, allow the engine switch to return
to the ON position.) Turn off choke.
CAUTION: Small engines may kick back. Do not
hold pull rope tightly in hand.
5. With spray nozzle pointed away from you or
anybody else, press trigger on spray gun to obtain
pressurized spray.
G E N E R A L W A S H I N G
TECHNIQUES.
1. Hold spray nozzle approximately one foot from
the surface being cleaned. Spray at an angle to get
under the material and lift it off.
2. When washing large objects, use chemical
injector to apply detergent (see section “How to use
the chemical injector”). Start washing from the
bottom and work up. Better chemical economy and
faster results will be obtained by allowing the
chemical to set 5-10 minutes.
After washing, rinse from the top down.
3. Cleaning heavy dirt or material away with a hard
stream of clear water is recommended before using a
cleaning agent.
PJE SERIES PRESSURE WASHER
OPERATOR’S MANUAL