Man E 0824 E 301 Скачать руководство пользователя страница 22

Страница: 22 / 48

Commissioning and operation

Starting

Danger:
Before starting the engine, ensure that nobody is in the danger area around
the engine.

Operation with asynchronous generator

Operate starter to crank engine with gas supply shut off and without ignition for a few
seconds (air purge).

Starting control will close throttle valve in gas mixer (gas mixer is not part of MAN’s ex-
tent of delivery).

Switch on ignition.

Solenoid valve for gas supply opens (not part of MAN’s extent of delivery).

Engine will start firing and run up to 1,300 to 1,400 rpm without generator load on id-
ling gas flow.

The starting control will move the throttle valve into operating position. Simultaneously,
the generator will be connected to the system.

Operation with synchronous generator

Operate starter and crank engine with gas supply shut off and without ignition for a few
seconds (air purge). The electronic speed governor (not part of MAN’s extent of deliv-
ery) has to be switched on at the same time.

Switch on ignition.

Solenoid valve for gas supply opens (not part of MAN’s extent of delivery).

Engine will start firing.

The electronic speed governor (nicht Lieferumfang von MAN) maintains the engine
speed at the value set on the set-point potentiometer.

Danger:
Ensure that the engine cannot be started by unauthorised persons.

Содержание E 0824 E 301

















































Результаты поиска

Содержание E 0824 E 301

Отзывы:

Man E 0824 E 301, Руководство по эксплуатации, Страница: 22 / 48

Результаты поиска

Содержание E 0824 E 301

Отзывы: