Mammoth 211404 Скачать руководство пользователя

Страница: 11 / 13

Mammoth Fans COMMERCIAL II SERIES |

TROUBLESHOOTING

Code

Desc.

Reason

Solution

E.SPD

Rapid failure

Controller application

Seek technical support from manufacturer

Improper setting of relevant
parameters for rapid detection

Adjust rapid detection threshold and F10.45
(rapid detection time)

Fan fault

Make sure that the fan is running normally.
If not, replace the fan and start up again

Note:

the percentage of output motor speed relative to F01.10 (maximum frequency) is greater than F10.44 (rapid detection

threshold), and the fault is reported after continuous F10.45 of rapid detection time. By F10.43 (the rapid protection action),
the fault detection and the motor operation mode can be set when the fault is detected.

Code

Desc.

Reason

Solution

E.TExx

Self-learning

failures

The output current of the
controller exceeds the
upper and lower limits

Check if the motor connection is correct, reset and
retry self-learning. If the error still occurs, contact
the Mammoth Fan support team.

Note:

where “xx” is self-learning faults ub code.

Code

Desc.

Reason

Solution

E. oUxx

Mid

acceleration/

moderate/

midspeed/

stop/over

-voltage fault

High voltage

Reduce the supply voltage to a specified range

Controller output or motor
short circuit

Check main circuit wiring, eliminate short circuit

Too short acceleration/
deceleration time

Determine whether the acceleration stops. The fault
detection increases F01.22 (acceleration time 1)
increases F01.23 (deceleration time 1)

Overvoltage suppression of
frequency rise may result in
accelerated overvoltage fault

Increase overvoltage suppression gain F10.13

Over-current suppression
of frequency-lowering
overvoltage fault

Decrease overcurrent suppression gain
F10.02 and reduce load

Surge voltage mixed
with input voltage

Add reactor to input side

Improper setting of speed
tracking parameters

Change of speed tracking parameter (F07.25~F07.28)

Note:

this fault is detected when the bus voltage exceeds the overvoltage point. Three phase input overvoltage point is 820 V,

single-phase input overvoltage point is 400 V.

Содержание 211404














Результаты поиска

Содержание 211404

Отзывы:

Похожие инструкции для 211404

Бренды по названию

Популярные бренды

Mammoth 211404, Инструкция по эксплуатации

Результаты поиска

Содержание 211404

Отзывы:

Похожие инструкции для 211404

Бренды по названию

Популярные бренды