Malyan MA10 Скачать руководство пользователя страница 15

15 

FCC Notice 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 
 
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

The equipment should be installed and operated with minimum distance 20cm between the 
radiator 

&

 your body.

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that int
erference will not occur in a particular installation. If this equipment does cause harmful interfere
nce to radio or television reception, which can be determined by turning the equipment off and o
n, the user is encouraged to try to correct the interference by one or more of the following measu
res: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is conn
ected. 
—Consult the dealer or an experienced radio/TV technician for help.  

 

Содержание MA10
















Отзывы: