background image

OWNER’S MANUAL

ii

i

ELECTRICAL

BEFORE USE

 Carefully remove packaging. Take care not to damage the bed frame or any included parts.

   Carefully read and follow the set up and installation instructions included with the product.

IMPORTANT: PLEASE READ ALL SAFETY INSTRUCTIONS THOROUGHLY 

BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS.

PACEMAKERS

SMALL CHILDREN AND PETS

HOME USE / HOSPITAL DISCLAIMER

WEIGHT RESTRICTIONS

 This product is for use on a standard 120-volt circuit.

   Always use a grounded, electrical surge protection device with this product. This product should 

be plugged directly into the surge protection device and the surge protection device should be 

plugged directly into a wall outlet.

 Only connect this product to a properly grounded outlet.  

 Always unplug this bed from the electrical outlet before cleaning or servicing.

 Never operate with a damaged cord or plug. Keep the cord away from this product’s moving parts.  

 Keep the cord away from heated surfaces.

 Do not use this product outdoors.

 

 Some pacemakers may detect motion by this product as a false sense of movement or exercise. This may or may 

not affect your pacemaker. Talk to a physician to address any concerns.

 

 Immediately dispose of all packing materials that may pose a suffocation risk.  

 

  Do not allow children or pets to play on or under the bed. Children should not operate this 

product without adult supervision.

 

 This product is designed solely for in-home use and not as a hospital bed. The product has not been tested to 

meet hospital standards. Do not use with oxygen or other flammable gasses. 

 

 The recommended weight restrictions for the Structures™ M455 Adjustable Base are as follows: (all weights 

include the weight of the mattress and bedding).

     Twin: 850 lbs. | Full: 850 lbs. | Twin XL: 850 lbs. | Queen: 850 lbs. | Split Beds: 850 lbs. per side

  This product will support the recommended weight limits when weight is distributed evenly across the base. This 

product is not designed to support or lift this amount in the head or foot sections alone. Consumers should not 

enter or exit the bed when any portion of it is in the raised position. Do not sit on the head or foot sections while 

in the raised position. Exceeding the recommended weight restrictions or other misuse of this product could 

damage the bed and void the warranty.

WARNINGS

Содержание Structures M455





















Отзывы: