MALONE
R
MALONE
R
DownLoader
DownLoader
TM
J-STYLE FOLDING KAYAK CARRIER
12’ Safety Lines
Jawz Universal Adapters
Mounting Bolts
Kayak Carriers
Load Straps
T-Knobs
60mm
70mm
Installation & Loading Instructions - Please Read Before Beginning
Veuillez lire les instructions avant d’entreprendre l’installation et le chargement
1
3
2
. Insert Mounting Bolt through one hole of a Jawz adapter.
Insert washer and loosely apply a T-knob. See image 2.
. Faites passer le boulon de fixation dans l’un des trous
d’un adaptateur Jawz puis vissez légèrement un bouton
en ‘‘T’’ à la base du boulon. (Figure 2)
. Prior to installation, insert a bolt into the mounting holes in
the bottom of the carriers. Push upward to open the two
mounting hole covers located in the Base pads.
. Insert a Mounting Bolt into one mounting hole from the top
side. Rotate and close the mounting hole cover.
See image 1.
. Insérez un boulon de fixation dans l’un des trous hexagonaux
situés sur le côté supérieur du support.
(Figure 1)
. Place the carrier onto the front cross bar with the boarding
ramp facing out. Swing the Jawz under the cross bar as
shown. See image 3.
. Placez le support sur la barre transversale avant, la rampe
de chargement vers l’extérieur. Faites passer l’adaptateur
Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)
1
Mounting Bolt Washers
Base Pad
Covers
The LoadRoller
tm
attaches to the Axis
tm
and makes loading easier and safer.
CARGO CARRIERS
23
www.maloneautoracks.com
CARGO CARRIERS
Our hitch based cargo management systems are carefully produced from high grade steel tubing and
powder coated to resist corrosion. For "open air" transit, the Katahdin roof basket delivers both style
and large volume capability. All Malone cargo carriers are covered with a Lifetime Warranty.
TM
61" x 38" x 10" high
MPG311
KATAHDIN
Roof Basket
TM
Features Include:
Easy assembly
Fold-away design
2" receiver wtih pin
Powder coat finish
Steel mesh bottom
Dimensions: 60x19x2"
Capacity: 500 lbs
Weight: 42 lbs
Lifetime warranty
Features Include:
Two piece design assembles in minutes - Powder coated steel
construction - Safely transport loads up to 165 LB - Universal mounting hardware
Custom fairing for less wind noise - Requires a minimum 25" cross bar span
HitchKing
Cargo Tray
TM
HitchKing2
Cargo Tray
TM
Features Include:
Fold-away design
2" receiver with pin
Powder coat finish
6.25" safety side rails
Steel mesh bottom
Dimensions: 58x19x6.25"
Capacity: 800 lbs
Weight: 55 lbs
Lifetime warranty
TM
Axis
Load Extender
Features Include:
8 height settings (56" - 63")
10 width settings (32"- 48")
Side arm load containment
2" receiver wtih pin
Powder coat finish
Dimensions: 63x48"
Capacity: 500 lbs
Weight: 33 lbs
Lifetime warranty
MPG907
MPG905
MPG906
TRUCK BED EXTENDER ROLLER
L
oad
R
oller
LoadRoller
tm
with
mounting hardware (1)
MPG909
● With your Axis
tm
assembled and installed, remove the locking pin from one of the wings/end posts and slide
the wing outwards.
● Make sure the mounting bolts and washers are removed and insert the LoadRoller
tm
into the attached wing/
end posts lower mounting hole.
● Reinstall the other wing/end post, aligning the LoadRoller
tm
with the lower hole in the wing/end post. Adjust as
needed to center the LoadRoller
tm
and insert the locking pin for the wing/end post.
● Secure the roller to the wings/end posts with the washers and lock nuts on each side. Be careful not to
over-tighten as the roller should move freely.
