Mallinckrodt INOblender 10004 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

Mallinckrodt INOblender 10004 Скачать руководство пользователя страница 13

Part No. 20732 Rev-02

2014-02

7

Setup

Check the INOMAX gas cylinder for the correct

product identity labels, cylinder concentration

(800 or 400 ppm) and expiration date. Ensure the

INOMAX gas cylinder has > 14 bar (200 psig).

1. Connect a high-pressure regulator to an

INOMAX cylinder and hand tighten the fitting

to the INOMAX cylinder.

2. Connect the INOMAX regulator hose to the

INOblender inlet hose using the quick

connect fittings.

3. Connect the oxygen supply to the O

2

inlet

fitting. (see part list for correct oxygen hose)

Note: 3.5 bar (50 psig) nominal

1. Make sure the NO dose setting dial is

turned to zero.

2. Attach a manual resuscitation bag to the

INOblender outlet fitting.

To oxygen source

The INOblender is now set up. Proceed to Section 3/Pre-use Checkout.

1

2

3

1

2

Note: • For the CGA-type INOMAX regulator

connector, ensure the white plastic tip

is not chipped or cracked. Remove and

replace as necessary. (see Replacing the

tip on the INOMAX regulator, Page 16).

• For the ISO-type regulator connector,

check that the O-ring is present and is

not damaged (see Replacing the tip on

the INOMAX regulator, Page 17).

«
...
11
12
13
14
15
...
»

Содержание INOblender 10004







































Отзывы:

Нет отзывов