manualshive.com logo in svg

Malcotools FasGroov FGVK, Инструкция

Поделиться
Скачать
Malcotools FasGroov FGVK Скачать руководство пользователя страница 11

w w w . m a l c o t o o l s . c o m

VEE-GROOV FABRICATION

#1
GRAY

#2/4
DARK
ORANGE

#2/4
DARK
ORANGE

#3
ORANGE

#5
BLUE

W1

H1

W2

H2

Face the factory made female shiplap edge of a 
standard four foot ductboard section. Place the 
FasGroov #1 Tool against the left edge of the 
ductboard. Push the FasGroov #1 Tool closely 
along the left edge to produce a female shiplap 
groove.

Set the FasGroov Square on top of the duct-
board. Place the ruled edge along the factory 
made female shiplap edge. Measure the desired 
inside duct width dimension (W1) and align 
with the right edge of cut made previously by 
the FasGroov #1 Tool. Place the FasGroov Vee-
Tool against the slide edge and push along to 
produce a vee groove.
Move the FasGroov Square to the right and mea-
sure the desired inside duct height dimension 
(H1). Align dimension with the right edge of cut 
previously made by the FasGroov Vee-Tool.

#1  TOOL

VEE TOOL

#3 TOOL

CUT FLAP

11

Содержание FasGroov FGVK













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды