Maktec MT560 Скачать руководство пользователя страница 7

FUNCTIONAL DESCRIPTION 

 

CAUTION: 

• 

Always be sure that the tool is switched off and unplugged 
before adjusting or checking function on the tool. 

Adjusting depth of cut 

 

CAUTION: 

• 

After adjusting the depth of cut, always tighten the 
clamping screws securely. 

Loosen the clamping screw on the depth guide and move 
the base up or down. At the desired depth of cut, secure 
the base by tightening the clamping screw. 

1

 

 

004027 

For  cleaner,  safer  cuts,  set  cut  depth  so  that  no  more 
than  one  blade  tooth  projects  below  workpiece.  Using 
proper cut depth helps to reduce potential for dangerous 
KICKBACKS which can cause personal injury. 

Bevel cutting 

1

1

 

 

004028 

Loosen two clamping screws on the bevel plates on the 
front and back of the base. Set for the desired angle (0° - 
45°)  by  tilting  accordingly,  then  tighten  the  clamping 
screws securely. 

Sighting 

1

B

A

 

 

004029 

For straight cuts, align the A position on the front of the 
base with your cutting line. For 45° bevel cuts, align the B 
position with it. 

Switch action 

1

2

 

 

004030 

CAUTION: 

• 

Before  plugging  in  the  tool,  always  check  to  see 
that the switch trigger actuates properly and returns 
to the "OFF" position when released. 

For tool with lock button 

To start the tool, simply pull the switch trigger. Release 
the switch trigger to stop. 
For continuous operation, pull the switch trigger and then 
push in the lock button. 
To stop the tool from the locked position, pull the switch 
trigger fully, then release it. 

For tool without lock button 

To start the tool, simply pull the switch trigger. Release 
the switch trigger to stop. 

ASSEMBLY 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before carrying out any work on the tool. 

Removing or installing saw blade 

1

2

 

 

004031 

CAUTION: 

• 

Be sure the blade is installed with teeth pointing up 
at the front of the tool. 

• 

Use only the Makita wrench to install or remove the 
blade. 

To  remove  the  blade,  press  the  shaft  lock  so  that  the 
blade cannot revolve and use the wrench to loosen the 
hex  bolt  counterclockwise.  Then  remove  the  hex  bolt, 

1. Hex wrench 
2. Shaft lock 

1. Switch trigger 
2. Lock button 

1. Base plate 

1. Clamping screw

1. Clamping screw

Содержание MT560













Отзывы: