Maktec MT370 Скачать руководство пользователя страница 9

9

For cutting circles between 121 mm and 221 mm in radius.

NOTE:

Circles between 172 mm and 186 mm in radius cannot be cut using this
guide.

Align the center hole in the straight guide with the center of the circle to be cut.
Drive a nail less than 6 mm in diameter into the center hole to secure the
straight guide. Pivot the tool around the nail in clockwise direction.

Trimmer guide

Trimming, curved cuts in veneers for furniture and the like can be done easily
with the trimmer guide. The guide roller rides the curve and assures a fine cut.

Install the trimmer guide on the tool base with the clamp screw (A). Loosen the
clamp screw (B) and adjust the distance between the bit and the trimmer guide
by turning the adjusting screw (1 mm per turn). At the desired distance, tighten
the clamp screw (B) to secure the trimmer guide in place.

1. Wing nut

2. Wave washer

3. Flat washer

4. Guide plate

5. Straight guide

6. Centre hole

7. Bolt

1

2

3

4

5

6

7

001994

1. Nail

2. Center hole

3. Straight guide

1
2
3

005438

005439

1. Clamp screw(A)

2. Adjusting screw

3. Clamp screw(B)

4. Trimmer guide

1
2

3

4

005440

Содержание MT370

















Отзывы: