manualshive.com logo in svg

Maktec MT230, Инструкция по эксплуатации

Поделиться
Скачать
Maktec MT230 Скачать руководство пользователя страница 8

8 

For all countries other than European countries 

1

 

 

007761 

To start the tool, simply pull the switch trigger. Release 
the switch trigger to stop. 

 

WARNING: 

• 

NEVER  use  tool  without  a  fully  operative  switch 
trigger.  Any  tool  with  an  inoperative  switch  is 
HIGHLY  DANGEROUS  and  must  be  repaired 
before further usage. 

ASSEMBLY 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before carrying out any work on the tool. 

Installing or removing saw blade 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before installing or removing the blade. 

• 

Use  only  the  Makita  wrench  provided  to  install  or 
remove  the  blade.  Failure  to  do  so  may  result  in 
overtightening  or  insufficient  tightening  of  the  hex 
bolt. This could cause an injury. 

When removing or installing the blade, keep the handle 
in the raised position. 

1

2

 

 

007771 

To remove the blade, use the wrench to loosen the hex 
bolt  holding  the  center  cover  by  turning  it 
counterclockwise.  Raise  the  blade  guard  and  center 
cover. 

1

 

 

007774 

Press  the  shaft  lock  to  lock  the  spindle  and  use  the 
wrench  to  loosen the  hex  bolt  clockwise.  Then  remove 
the hex bolt, outer flange and blade. 

1

2

 

 

007770 

To install the blade, mount it carefully onto the spindle, 
making sure that the direction of the arrow on the surface 
of  the  blade  matches  the  direction  of  the  arrow  on  the 
blade case. Install the outer flange and hex bolt, and then 
use  the  wrench  to  tighten  the  hex  bolt  (left-handed) 
securely counterclockwise while pressing the shaft lock. 

1

2

3

4

 

 

007808 

1

2

3

4

5

6

 

 

004852 

CAUTION: 

• 

The  ring  25.4  mm  or  30  mm  in  outer  diameter  is 
factory-installed onto the spindle. Before mounting 
the blade onto the spindle, always be sure that the 
correct  ring  for  the  arbor  hole  of  the  blade  you 
intend to use is installed onto the spindle. 

1. Spindle 
2. Flange 
3. Saw blade 
4. Flange 
5. Hex bolt 
6. Ring 

1. Blade case 
2. Arrow 
3. Arrow 
4. Saw blade 

1. Hex bolt 
2. Wrench 

1. Hex bolt 

1. Wrench 
2. Center cover 

1. Switch trigger 

Содержание MT230

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды