Makita XSL01, Инструкция по эксплуатации

Страница: 14 / 68

14
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
1 2 3
001555
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
(1) (2) (3) (4)
1 2
Fig.A
001556
2
(1)
(2)
(1)
(2)
(2)
(1)
(2)
(1)
(1)
(2)
(3)
(4)
1
001557
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length
at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use
several pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the
bevel angle and miter angle as indicated in the table
(A) and position the moldings on the top surface of
the saw base as indicated in the table (B).
In the case of left bevel cut
M ol d i ng
posi t io n i n
Fi g . A
Beve l ang l e M i ter ang l e
Fo r ou t si de
co rner
Fo r i n si de
co rner
52 / 3 8° t yp e 4 5 ° t yp e
R i ght 3 1.6°
4 5 ° t yp e
L eft 33 .9° L eft 30 °
52 / 3 8° t yp e
L eft 3 1.6° L eft 35 . 3 °
R i ght 35 . 3 °
R i ght 35 . 3 ° R i ght 3 1.6°
(1)
( 2 )
( 3 )
(4)
T a bl e (A)
006361
M ol d i ng
posi t io n i n
Fi g . A
M ol d i ng edge aga i n s t
g ui de fen c e
(1)
C e ili ng co nta c t edge s h oul d
b e aga i n s t g ui de fen c e .
C e ili ng co nta c t edge s h oul d
b e aga i n s t g ui de fen c e .
Fo r
ou t si de
co rner
Fi n is hed pi e c e
will b e o n the
L eft si de o f
bl ade .
Fi n is hed pi e c e
will b e o n the
R i ght si de o f
bl ade .
Fo r i n si de
co rner
W a ll co nta c t edge s h oul d b e
aga i n s t g ui de fen c e .
Fi n is hed pi e c e
( 2 )
( 3 )
(4)
T a bl e ( B )
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
•
Tilt and secure bevel angle setting to
33.9° LEFT.
•
Adjust and secure miter angle setting to
31.6° RIGHT.
•
Lay crown molding with its broad back
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
•
The finished piece to be used will
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
M ol d i ng
posi t io n i n
Fi g . A
Beve l ang l e M i ter ang l e
Fo r ou t si de
co rner
Fo r i n si de
co rner
52 / 3 8° t yp e 4 5 ° t yp e
R i ght 3 1.6°
4 5 ° t yp e
R i ght 33 .9° R i ght 30 °
52 / 3 8° t yp e
L eft 3 1.6° L eft 35 . 3 °
R i ght 35 . 3 °
R i ght 35 . 3 ° R i ght 3 1.6°
(1)
( 2 )
( 3 )
(4)
T a bl e (A)
006363
1. Inside corner
2. Outside corner
1. Inside corner
2. Outside corner
1. 52/38
ﾟ
type
crown molding
2. 45
ﾟ
type crown
molding
3. 45
ﾟ
type cove
molding