background image

Automatic speed change function 

1

015142 

Mode indicator status

Operation mode

High speed mode

High torque mode

015098 

This tool has "high speed mode" and "high torque 
mode". It automatically changes operation mode 
depending on the work load. When mode indicator lights 
up during operation, the tool is in high torque mode. 

Tool / battery protection system 

The tool is equipped with a tool/battery protection 
system. This system automatically cuts off power to the 
motor to extend tool and battery life. 
The tool will automatically stop during operation if the 
tool or battery is placed under one of the following 
conditions. In some conditions, the indicator lights up. 

Overload protection 

When the tool is operated in a manner that causes it to 
draw an abnormally high current, the tool automatically 
stops without any indications. In this situation, turn the 
tool off and stop the application that caused the tool to 
become overloaded. Then turn the tool on to restart. 

Overheat protection for tool 

When the tool is overheated, the tool stops 
automatically and the battery indicator shows following 
state. In this situation, let the tool cool before turning the 
tool on again. 

Battery indicator

Tool is overheated

On

Off

Blinking

015140 

Releasing protection lock 

When the protection system works repeatedly, the tool is 
locked and the battery indicator shows the following state. 

Protection lock works

Battery indicator

On

Off

Blinking

015200 

In this situation, the tool does not start even if turning the tool 
off and on. To release the protection lock, remove the battery, 
set it to the battery charger and wait until the charging finishes. 

Shaft lock 

CAUTION: 

• 

Never actuate the shaft lock when the spindle is
moving. The tool may be damaged. 

1

015081 

Press the shaft lock to prevent spindle rotation when 
installing or removing accessories. 

ASSEMBLY 

CAUTION: 

• 

Always be sure that the tool is switched off and the 
battery cartridge is removed before carrying out
any work on the tool. 

Installing side grip (handle) 

CAUTION: 

• 

Always be sure that the side grip is installed
securely before operation.

015083 

Screw the side grip securely on the position of the tool 
as shown in the figure. 

1. Shaft lock 

1. Mode indicator

Содержание XAG04

















Отзывы: