16 ENGLISH
Connecting the tool
NOTE: If the bent pipe assembly is attached to the
hose, remove it beforehand.
To connect a tool to the cleaner, the dedicated hose
and/or additional parts are required. Depending on your
cleaner model, you need to replace the hose and/or
prepare additional parts.
Refer to the following table for details.
Supplied
hose
diameter
Hose end type
Action
ø28 mm
without part
Attach the front cuff.
with snap-on part
Replace the hose end
(snap-on part) with the front
cuff.
The hose end can be removed
by turning it counterclockwise.
ø32 mm
with snap-on part
Replace the hose with the one
for dust extraction (ø28 mm,
with front cuff).
ø38 mm
with snap-on part
Replace the hose with the one
for dust extraction (ø28 mm,
with front cuff).
with front cuff 38
Attach the joint 22-38 or the
front cuff 24.
NOTE:
Always use a suitable front cuff. When using
the front cuff 24, attach it to the front cuff 22 that is
connected to the hose.
►
Fig.22:
1.
Front cuff 22
2.
Front cuff 24
When using ø28 mm dust extraction
hose
1.
Attach the front cuff to the hose for dust extraction.
When connecting the front cuff, make sure that it is
securely screwed on the hose.
2.
Connect the front cuff to the tool's extraction
outlet.
►
Fig.23:
1.
Front cuff
2.
Extraction outlet
3.
Hose
The front cuff can be detached by turning it counter
-
clockwise while holding the hose.
When using ø38 mm hose with front
cuff 38
1.
Twist and insert the joint or the front cuff to the
inlet part on the hose, depending on the tool that you
are going to connect.
2.
Connect the front cuff to the tool's extraction
outlet.
►
Fig.24:
1.
Joint
2.
Front cuff
3.
Extraction outlet
4.
Hose
To remove the joint and the front cuff, follow the installa
-
tion procedures in reverse.
Installing filter bag / dust bag
Optional accessory
CAUTION:
Do not use a damaged filter bag.
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust
or particles may be exhausted from the cleaner
and they may cause respiratory disease to the
operator.
NOTICE:
When the filter bag is already full,
replace with new one. When the dust bag is
already full, empty it.
Continuous use with the filter
bag/dust bag full results in reduced suction power.
NOTICE:
To prevent dust from getting into the
motor:
—
Make sure that the filter bag/dust bag is
installed before use.
—
Do not use a broken or ripped bag.
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the filter bag/dust bag.
NOTICE:
The filter bag/dust bag for the cleaner
is an important component for maintaining the
appliance performance. Using non-genuine filter
bag/dust bag may cause smoke or ignition.
NOTE:
When the filter bag/dust bag is not installed in
the cleaner, the front cover does not close completely.
►
Fig.25
1.
Unlock the lever and open the dust box cover.
►
Fig.26:
1.
Lever
2.
Dust box cover
2.
Insert the filter bag into the slit on the upper side of
the room as illustrated.
►
Fig.27:
1.
Slit
2.
Filter bag
Содержание VC008G
