![background image](http://html1.mh-extra.com/html/makita/rt0702cx3j/rt0702cx3j_instruction-manual_4011511016.webp)
16 ENGLISH
Trimmer guide
Optional accessory
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The
guide roller rides the curve and assures a fine cut.
►
Fig.23
1.
Install the trimmer guide and guide holder on the
base with the clamping screw (A).
2.
Loosen the clamping screw (B) and adjust the
distance between the trimmer bit and the trimmer guide
by turning the adjusting screw (1 mm per turn). At the
desired distance, tighten the clamping screw (B) to
secure the trimmer guide in place.
►
Fig.24:
1.
Adjusting screw
2.
Guide holder
3.
Trimmer guide
3.
When cutting, move the tool with the guide roller
riding the side of the workpiece.
►
Fig.25:
1.
Workpiece
2.
Trimmer bit
3.
Guide roller
Tilt base
Optional accessory
The tilt base is used for trimming the edge of laminate
sheet or similar materials.
The tilt base is convenient for chamfering.
1.
Place the tool onto the tilt base, loosen the clamp
-
ing screws, and tilt the tool at the desired angle.
2.
Close the locking lever at the desired protrusion of the
trimmer bit, and tighten the clamping screws at the desired angle.
3.
Firmly clamp a straight board to the workpiece and
use it as a guide against the tilt base. Feed the tool in
the direction of the arrow.
►
Fig.26:
1.
Clamping screws
2.
Locking lever
Using the tilt base protector with the base
The tilt base protector (square) removed from the tilt
base can be mounted on the base. The shape of the
base protector can be changed from round to square.
1.
Remove the tilt base protector from the tilt base by
loosening and removing the four screws.
2.
Mount the tilt base protector on the base.
►
Fig.27:
1.
Tilt base protector
2.
Screw
Offset base
Optional accessory
The offset base is used for trimming the edge of lami
-
nate sheet or similar materials.
The offset base is convenient for work in a tight area.
►
Fig.28
Using the tool with the offset base
1.
Before installing the tool on the offset base, remove the
collet nut and collet cone by loosening the collet nut.
►
Fig.29:
1.
Pulley
2.
Collet nut
3.
Collet cone
2.
Install the pulley on the tool by pressing the shaft
lock and firmly tightening the pulley with a wrench.
►
Fig.30:
1.
Wrench
2.
Pulley
3.
Shaft lock
3.
Place the collet cone and screw the collet nut on
the offset base as shown in the figure.
►
Fig.31:
1.
Collet nut
2.
Collet cone
4.
Mount the offset base on the tool.
►
Fig.32
5.
Hook the belt over the pulley using a screwdriver
and make sure that its entire belt width fits over the
pulley completely.
►
Fig.33:
1.
Pulley
2.
Belt
6.
Close the locking lever.
►
Fig.34:
1.
Locking lever
7.
Install the trimmer bit as follows.
Lay down the tool with the offset base. Insert the hex
wrench into the hole in the offset base.
With the hex wrench held in the position as shown in
the figure, insert the trimmer bit into the collet cone on
the shaft of the offset base from the opposite side and
tighten the collet nut firmly with a wrench.
►
Fig.35:
1.
Wrench
2.
Hex wrench
3.
Trimmer bit
8.
To remove the trimmer bit, follow the installation
procedure in reverse.
Using the base with the offset base
plate and grip attachment
The offset base can also be used with a base and a grip
attachment (optional accessory) for more stability.
►
Fig.36
1.
Loosen the screws and remove the upper section
from the offset base. Put aside the upper section of the
offset base.
►
Fig.37:
1.
Screws
2.
Offset base plate
3.
Upper
section of the offset base
2.
Mount the offset base plate with four screws and the
grip attachment with two screws on the offset base plate.
Screw a bar type grip (optional accessory) onto the grip
attachment. In another way of use, the knob type grip which
is removed from a plunge base (optional accessory) can be
installed on the grip attachment. To install the knob type grip,
place it on the grip attachment and secure it with a screw.
With bar type grip
►
Fig.38:
1.
Bar type grip
2.
Grip attachment
3.
Offset
base plate
With knob type grip
►
Fig.39:
1.
Screw
2.
Knob type grip
3.
Grip
attachment
Using the tool with the plunge base
Optional accessory
CAUTION:
When using as a router, hold the
tool firmly with both hands.
1.
To use the tool as a router, install the tool on a
plunge base (optional accessory) by pressing it down
fully. Either knob type grip or bar type grip (optional
accessory) can be used according to your work.
►
Fig.40:
1.
Plunge base
2.
Bar type grip
Содержание RT0702CX3J
