5 ENGLISH
Service
1.
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
2.
Follow instruction for lubricating and chang-
ing accessories.
Router safety warnings
1.
Hold the power tool by insulated gripping
surfaces only, because the cutter may contact
its own cord.
Cutting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3.
The cutter bit shank must match the designed
collet chuck.
4.
Only use a bit that is rated at least equal to the
maximum speed marked on the tool.
5.
Wear hearing protection during extended
period of operation.
6.
Handle the router bits very carefully.
7.
Check the router bit carefully for cracks or
damage before operation. Replace cracked or
damaged bit immediately.
8.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
9.
Hold the tool firmly with both hands.
10.
Keep hands away from rotating parts.
11.
Make sure the router bit is not contacting the
workpiece before the switch is turned on.
12.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or wob-
bling that could indicate improperly installed bit.
13.
Be careful of the router bit rotating direction
and the feed direction.
14.
Do not leave the tool running. Operate the tool
only when hand-held.
15.
Always switch off and wait for the router bit to
come to a complete stop before removing the
tool from workpiece.
16.
Do not touch the router bit immediately after
operation; it may be extremely hot and could
burn your skin.
17.
Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
18.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
19.
Always use the correct dust mask/respirator for
the material and application you are working with.
20.
Place the tool on stable area.
Otherwise falling
accident may occur and cause an injury.
21.
Keep cord away from your foot or any objects.
Otherwise an entangled cord may cause a falling
accident and result in personal injury.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Adjusting the depth of cut
4
7
8
1
5
6
2
3
Fig.1
►
1.
Lock lever
2.
Adjusting hex bolt
3.
Stopper block
4.
Adjusting knob
5.
Depth pointer
6.
Stopper pole
7.
Stopper pole setting nut
8.
Fast-feed button
1.
Place the tool on a flat surface. Loosen the lock
lever and lower the tool body until the router bit just
touches the flat surface. Tighten the lock lever to lock
the tool body.
2.
Turn the stopper pole setting nut counterclock-
wise. Lower the stopper pole until it makes contact
with the adjusting hex bolt. Align the depth pointer with
the "0" graduation. The depth of cut is indicated on the
scale by the depth pointer.
3.
While pressing the fast-feed button, raise the
stopper pole until the desired depth of cut is obtained.
Minute depth adjustments can be obtained by turning
the adjusting knob (1 mm per turn).
4.
By turning the stopper pole setting nut clockwise,
you can fasten the stopper pole firmly.
5.
Now, your predetermined depth of cut can be
obtained by loosening the lock lever and then lowering
the tool body until the stopper pole makes contact with
the adjusting hex bolt of the stopper block.
