Makita RP1801F Скачать руководство пользователя

Страница: 11 / 16

Dust nozzle set (Accessory)

009878

Use the dust nozzle for dust extraction. Install the dust

nozzle on the tool base using the thumb screw so that

protrusion on the dust nozzle fit to the notch in the tool

base.

Then connect a vacuum cleaner to the dust nozzle.

009877

How to use screw M6 x 135 for adjusting the

depth of cut

When using the tool with a router table available in the

market, using this screw allows an operator to obtain a

small amount of adjustment of the depth of cut from

above the table.

009934

1. Installing the screw and washer on the tool

•

Attach flat washer onto this screw.

•

Insert this screw through a screw hole in the tool

base and then screw in the threaded part in the

motor bracket of the tool.

009935

009929

009930

At this time, apply some grease or lubricating oil to the

inside of the screw hole in the tool base and the

threaded part in the motor bracket.

009932

1. Inside of the

screw hole in

the tool base

1. Screw M6x135

2. Threaded part in

the motor

bracket

1. Hole

1. Flat washer 6

2. Screw M6x135

1. Flat washer 6

2. Screw M6x135

1. Dust nozzle

2. Clamping screw

Содержание RP1801F

















Результаты поиска

Содержание RP1801F

Отзывы:

Похожие инструкции для RP1801F

Бренды по названию

Популярные бренды

Makita RP1801F, Инструкция по эксплуатации

Результаты поиска

Содержание RP1801F

Отзывы:

Похожие инструкции для RP1801F

Бренды по названию

Популярные бренды