![background image](http://html2.mh-extra.com/html/makita/mt-m0800/mt-m0800_instruction-manual_5176950006.webp)
6 ENGLISH
OPERATION
CAUTION:
•
Always use the side grip (auxiliary handle) and
firmly hold the tool by both side grip and switch
handle during operations.
►
Fig.7
Hammer drilling operation
CAUTION:
•
There is tremendous and sudden twisting force
exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with
chips and particles, or when striking reinforcing
rods embedded in the concrete. Always use the
side grip (auxiliary handle) and firmly hold the
tool by both side grip and switch handle during
operations. Failure to do so may result in the
loss of control of the tool and potentially severe
injury.
When drilling in concrete, granite, tile, etc., slide the
action mode changing lever to the position of
sym-
bol to use "rotation with hammering" action. Be sure to
use a tungsten-carbide tipped bit. Do not apply more
pressure when the hole becomes clogged with chips or
particles. Instead, run the tool at an idle, then remove
the bit partially from the hole. By repeating this several
times, the hole will be cleaned out.
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Drilling operation
CAUTION:
•
Pressing excessively on the tool will not speed
up the drilling. In fact, this excessive pressure
will only serve to damage the tip of your bit,
decrease the tool performance and shorten the
service life of the tool.
•
There is a tremendous force exerted on the tool/
bit at the time of hole break through. Hold the
tool firmly and exert care when the bit begins to
break through the workpiece.
•
A stuck bit can be removed simply by setting
the reversing switch to reverse rotation in order
to back out. However, the tool may back out
abruptly if you do not hold it firmly.
•
Always secure small workpieces in a vise or
similar hold-down device.
When drilling in wood, metal or plastic materials,
slide the action mode changing lever to the position
of
symbol to use "rotation only" action.
Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer
at the point to be drilled. Place the point of the bit in the
indentation and start drilling. Use a cutting lubricant
when drilling metals. The exceptions are iron and brass
which should be drilled dry.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
•
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY,
repairs, carbon brush inspection and replacement, any
other maintenance or adjustment should be performed
by Makita Authorized Service Centers, always using
Makita replacement parts.
Содержание MT M0800
