9 ENGLISH
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Opening center cap type safety
guard
Country specific
For the tools equipped with center cap type safety guard,
loosen the clamping screw first then raise the guard.
►
Fig.11:
1.
Clamping screw
Opening European type safety
guard
Country specific
For the tools equipped with European type safety guard,
loosen the clamping screw first then open the guard as
shown.
►
Fig.12:
1.
Clamping screw
►
Fig.13
►
Fig.14
Removing or installing cut-off wheel
CAUTION:
Be sure to tighten the toolless
clamp or hex bolt securely.
Insufficient tightening
may result in severe injury. When tightening the hex
bolt, use the socket wrench provided with the tool to
assure proper tightening.
CAUTION:
Always use only the proper inner
and outer flanges which are provided with the
tool.
CAUTION:
Always lower the safety guard
after replacing the wheel.
►
Fig.15:
1.
Inner flange
2.
Ring
3.
O-ring
4.
Cut-off
wheel
5.
Outer flange
6.
Toolless clamp /
Hex bolt
For LW1400
Raise the safety guard. Turn the toolless clamp coun-
terclockwise while holding down the shaft lock. Then
remove the toolless clamp, outer flange and cut-off
wheel. When removing the cut-off wheel, do not remove
the inner flange as well as the ring and O-ring.
►
Fig.16:
1.
Shaft lock
2.
Toolless clamp
To install the cut-off wheel, follow the removal proce-
dures in reverse. Make sure to fit the hole of cut-off
wheel to the ring and return the safety guard.
For LW1401
Raise the safety guard. Turn the hex bolt counterclock
-
wise using a socket wrench while holding down the shaft
lock. Then remove the hex bolt, outer flange and wheel.
►
Fig.17:
1.
Shaft lock
2.
Hex bolt
To install the wheel, follow the removal procedures in
reverse. Make sure to fit the hole of cut-off wheel to the
ring and return the safety guard.
OPERATION
CAUTION:
Proper handle pressure during
cutting and maximum cutting efficiency can
be determined by the amount of sparks that is
produced while cutting. Do not force the cut
by applying excessive pressure on the handle.
Reduced cutting efficiency, premature wheel wear, as
well as, possible damage to the tool, cut-off wheel or
workpiece may result.
Hold the handle firmly. Switch on the tool and wait until
the wheel attains full speed before lowering gently
into the cut. When the wheel contacts the workpiece,
gradually bear down on the handle to perform the cut.
When the cut is completed, switch off the tool and
wait
until the wheel has come to a complete stop
before
returning the handle to the fully elevated position.
Cutting capacity
Maximum cutting capacity varies depending on the
cutting angle and workpiece shape.
Max. cutting capacity with a brand-new cut-off
wheel
Cutting angle /
Workpiece shape
90°
45°
127 mm
127 mm
115 x 130 mm
102 x 194 mm
70 x 233 mm
115 x 103 mm
119 x 119 mm
106 x 106 mm
137 x 137 x 10 mm 100 x 100 x 10 mm
Securing workpiece
CAUTION:
Always place the thread holder on
the shaft threads when securing the workpiece.
Failure to do so may result in insufficient securing of
the workpiece. This could cause the workpiece to be
ejected or cause a dangerous breakage of the wheel.
While the thread holder is lifted, the vise plate can be
moved in and out quickly. To grip a workpiece, push the
handle until the vise plate contacts the workpiece then
return the thread holder. Turn the handle clockwise until
the workpiece is securely retained.
►
Fig.18:
1.
Handle
2.
Thread holder
3.
Vise plate
When the cut-off wheel has worn down considerably,
place a spacer block behind the workpiece as shown
Содержание LW1400
