![background image](http://html.mh-extra.com/html/makita/jr3060t/jr3060t_instruction-manual_224036006.webp)
6
Installing or removing the saw blade
CAUTION:
•
Always clean out all chips or foreign matter
adhering to the blade, blade clamp and/or slider.
Failure to do so may cause insufficient tightening
of the blade, resulting in a serious injury.
To install the saw blade, always make sure that the
blade clamp lever is in released position
on the
insulation cover before inserting the saw blade. If the
blade clamp lever is in fixed position, rotate the blade
clamp lever in the direction of the arrow so that it can be
locked at the released positon .
Fig.6
Insert the saw blade into the blade clamp as far as it will
go. The blade clamp lever rotates and the saw blade is
fixed. Make sure that the saw blade cannot be extracted
even though you try to pull it out.
Fig.7
NOTE:
•
If you do not insert the saw blade deep enough,
the saw blade may be ejected unexpectedly during
operation. This can be extremely dangerous.
If the lever is positioned inside the tool, switch on the
tool just a second to let the blade out as shown in the
figure.
Switch off and unplug the tool from the mains.
To remove the saw blade, rotate the blade clamp lever
in the direction of the arrow fully. The saw blade is
removed and the blade clamp lever is fixed at the
released position .
Fig.8
NOTE:
•
Keep hands and fingers away from the lever
during the switching operation. Failure to do so
may cause personal injuries.
•
If you remove the saw blade without rotating the
blade clamp lever fully, the lever may not be
locked in the released position . In this case,
rotate the blade clamp lever fully again, then make
sure that the blade clamp lever locked at the
released position .
OPERATION
Fig.9
CAUTION:
•
Always press the shoe firmly against the
workpiece during operation. If the shoe is removed
or held away from the workpiece during operation,
strong vibration and/or twisting will be produced,
causing the blade to snap dangerously.
•
Always wear gloves to protect your hands from hot
flying chips when cutting metal.
•
Be sure to always wear suitable eye protection
which conforms with current national standards.
•
Always use a suitable coolant (cutting oil) when
cutting metal. Failure to do so will cause
premature blade wear.
Press the shoe firmly against the workpiece. Do not
allow the tool to bounce. Bring the blade into light
contact with the workpiece. First, make a pilot groove
using a slower speed. Then use a faster speed to
continue cutting.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
•
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
Replacing carbon brushes
Fig.10
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
Fig.11
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
•
These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Recipro saw blades
•
Plastic carrying case
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Содержание JR3060T
Страница 49: ...49 ...
Страница 50: ...50 ...
Страница 51: ...51 ...
Страница 52: ...52 www makita com Makita Jan Baptist Vinkstraat 2 3070 Belgium Makita Corporation Anjo Aichi Japan 884592A966 ...