background image

P  

4

/1

6

R

epair

[3] DISASSEMBLY/ASSEMBLY
[3] -1. Base

Fig. 3

ASSEMBLING

ASSEMBLING, ADJUSTMENT

Base can be mounted to the machine by taking the reverse steps of Disassembling.

Note:

 Follow the important instructions described in 

Fig. 2A

.

          See 

Fig. 3

 for Assembling and Adjustment of 

Lock lever for clamping Guide Rule

[3] -2. Lock Lever for clamping Guide Rule

Guide rule

3. Applying the Torsion spring's long arm to the tab 

    of Base, put the Lock lever over M6x10 Hex bolt.  

    But do not push Lock lever down until you engage

    it with the Hex bolt in the step 5. 

4 . Lift up Lock lever so that its upper surface is flush

     with that of M6x10 Hex bolt, then rotate Lock lever

     independently.  Then adjust the Lock lever so that

     it can be locked in the position shown below.

5 . Push Lock lever down until it engages with

     M6x10 Hex bolt, then secure Lock lever with

     Stop ring E-6.

6. Make sure that:

    1) When Guide rule is clamped, Lock lever stops

         in the same position as you set in the step 4.

    2) With Guide rule removed, Lock lever returns to

         its initial position smoothly and exactly from the

         locking position..

M6x10 Hex bolt 

Mount Lock lever to Base and adjust its locking position when Guide rule attaching. (

Fig. 3

)

1. Fasten Guide rule to Base with M6x10 Hex bolt.

30 degrees

30 degrees

Stop ring E-6

Stop ring E-6

Be sure to mount E-8 Bow stop ring as shown below

for securely engaging Lever 45 with M6x20 Hex bolt.

Adjust Lever 45 so that it can be locked in the position

shown below when the machine’s cutting angle is

adjusted to 90 degrees.

30 degrees

Fig. 2A

Lever 45

M6x20 Hex bolt 

Flat washer 6 

E-8 Bow stop ring

Angular guide 

Angular guide section,

viewed from top 

Lever 45

2. Insert Torsion spring 11 into Lock lever with its

    short arm inserting in the square hole of Lock lever.

short arm

Torsion spring 11

Lock lever

tab

long arm

long arm

Содержание HS7100K

















Отзывы: