![background image](http://html.mh-extra.com/html/makita/hs010g/hs010g_instruction-manual_223927015.webp)
15 ENGLISH
Positive stopper
The positive stopper is useful for setting the designated angle
quickly. Turn the positive stopper so that the arrow on it points
your desired bevel angle (around 22.5°/45°/60°). Loosen the
lever and the clamping screw and then tilt the tool base until it
stops. The position where the tool base stops is the angle you
set with the positive stopper. Tighten the lever and clamping
screw with the tool base at this position.
►
Fig.12:
1.
Positive stopper
-1°-bevel cutting
To perform -1°-bevel cutting, loosen the lever and the
clamping screw. Set the bevel angle to -1° while turning
the stopper lever in the direction of the arrow. After that,
tighten the lever and the clamping screw.
►
Fig.13:
1.
Stopper lever
Sighting
For straight cuts, align the 0° position on the front of the
base with your cutting line. For 45° bevel cuts, align the
45° position with it.
►
Fig.14:
1.
Cutting line (0° position)
2.
Cutting line
(45° position)
Lighting the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp without running the tool, pull the
switch trigger without pressing the lock-off button.
To turn on the lamp with the tool running, press and hold
the lock-off button and pull the switch trigger.
The lamp goes out 10 seconds after releasing the switch trigger.
►
Fig.15:
1.
Lamp
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Electric brake
This tool is equipped with an electric blade brake. If the
tool consistently fails to quickly stop the circular saw
blade after switch lever release, have tool serviced at a
Makita service center.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
Electronic function
The tools equipped with electronic function are easy to
operate because of the following feature(s).
Soft start feature
Soft start because of suppressed starting shock.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Hex wrench storage
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
►
Fig.16:
1.
Hex wrench
Installing or removing circular saw blade
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the tool.
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
1.
Loosen the lever on the depth guide and move the base down.
►
Fig.17:
1.
Lever
2.
Install the inner flange, ring (country specific), circular
saw blade, outer flange and hex bolt. At this time, align the
direction of the arrow on the blade with the arrow on the tool.
For tool without the ring
►
Fig.18:
1.
Hex bolt
2.
Outer flange
3.
Circular saw
blade
4.
Inner flange
5.
Arrow on the circular
saw blade
6.
Arrow on the tool
For tool with the ring
►
Fig.19:
1.
Hex bolt
2.
Outer flange
3.
Circular saw
blade
4.
Ring
5.
Inner flange
6.
Arrow on the
circular saw blade
7.
Arrow on the tool
3.
Press the shaft lock fully so that the circular saw blade
cannot revolve and use the hex wrench to tighten the hex bolt.
►
Fig.20:
1.
Shaft lock
2.
Hex wrench
3.
Loosen
4.
Tighten
To remove the circular saw blade, follow the installation
procedure in reverse.
For tool with the inner flange for other
than 15.88 mm hole-diameter saw blade
The inner flange has a certain diameter protrusion on one
side of it and a different diameter protrusion on the other side.
Choose a correct side on which protrusion fits into the saw
blade hole perfectly. Mount the inner flange onto the mounting
shaft so that the correct side of protrusion on the inner flange
faces outward and then place saw blade and outer flange.
►
Fig.21:
1.
Mounting shaft
2.
Inner flange
3.
Circular
saw blade
4.
Outer flange
5.
Hex bolt
WARNING:
BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING:
Make sure that the protrusion "a"
on the inner flange that is positioned outside fits
into the saw blade hole "a" perfectly.
Mounting the
blade on the wrong side can result in the dangerous
vibration.
Содержание HS010G
