manualshive.com logo in svg

Makita HR4500C, Руководство пользователя

Поделиться
Скачать
Makita HR4500C Скачать руководство пользователя страница 5

R

epair

P 5 / 16

< 1 > Lubrication

Apply MAKITA grease No.00 to the following parts in order to prevent unusual abrasion and overheating.

Apply to O ring 27.

Striker

Ring 38

Apply to the inside.

Spiral bevel gear 36

Apply to the outside and teeth portion.

Rod

Apply to hole for 
crank shaft accepting.

Piston

Apply to the whole part of Impact bolt.

Oil seal 15 to be
assembled to gear side shaft
of armature

Oil seal 35

Apply to the lip portion.

Gear housing

Slide sleeve

Apply to the lip portion.

Torque limiter

Spur gear 10

Apply to this portion where
spur gear 10 does not engage 
torque limiter.

<2> Disassembling Change Lever Complete

     Set Change Lever Complete at neutral position,
     and  slightly hit the back side of lock button with a plastic hammer to remove it.
    (See Fig.1.) 

Fig. 1

plastic hammer

Lock button

Change lever
at neutral position.

Apply to O ring 27.

Apply to needle bearing.

Apply to this portion where
spur gear 10 does not engage 
torque limiter.

Содержание HR4500C

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды