background image

Specifications

C

ONCEPTION AND MAIN APPLICATIONS

Models No.

 Description

PRODUCT

P 1 / 16

Dimensions : mm  ( " )

Width  (W)

Height (H) 

Length (L)

118mm (4-5/8")

488mm (19-1/4")

For matured line-up of SDS-Max Rotary Hammers, Model HR4500C
has been developed as a sister model to HR4000C(40mm;1-3/4") and
HR5001C(50mm;2")  which are already popular to users around the
world. 

HR4500C

Rotary Hammer 45mm (1-3/4")

278mm (11")

Continuous Rating (W)

Voltage (V) Current (A) Cycle (Hz)

Input

Output

Max. Output(W)

120

110

13

50/60

1,300

600

1,500

100

15

50/60

1,300

600

1,500

13

 50/60

1,250

600

1,500
1,500
1,500
1,500

220

6.6

50/60

1,300

600

230

6.6

50/60

1,300

600

240

6.8

50/60

1,300

600

T

ECHINICAL INFORMATION

Performing excellent drilling in concrete within the diameter range
from 25mm(1") to 45mm(1-3/4"), it also has the same features and 
benefits as HR4000C and HR5001C.

Hammer Grease (30cc), Blow-out Bulb, Dust Cup 5, Dust Cup 9, Bull Point, Cold Chisel, Scaling Chisel,
Clay Spade, Bushing Tool, Rammer, Safety Goggles, Core Bit Adapter,
Core Bits; Hole diameter : 20mm(13/16"), 30mm(1-3/16"), 35mm(1-3/8"), 40mm(1-9/16"), 45mm(1-3/4"),
                                            54mm(2-1/8"), 65mm(2-9/16"), 79mm(3-1/8"), 105mm(4-1/8"), 118mm(4-5/8")
Tungusten-carbide Tipped Bits; Bit diameter : 10mm(3/8"), 10.5mm(7/16"), 11mm(7/16"), 12mm(15/32"), 
                                                                          12.5mm(1/2"), 12.7mm(1/2"), 13.5mm(1/2"), 14.3mm(9/16"),
                                                                          14.5mm(9/16"), 16mm(5/8"), 17mm(11/16"), 17.5mm(11/16"),
                                                                          18mm(11/16"), 19mm(3/4"), 20mm(13/16"), 21.5mm(7/8"), 
                                                                          22mm(7/8"). 24mm(15/16"), 25mm(1"), 25.4mm(1"), 26mm(1"),
                                                                          28mm(1-1/8"),  30mm(1-3/16"), 32mm(1-1/4"), 35mm(1-3/8"), 
                                                                          38mm(1-1/2")

120 - 240

1,250 - 2,550

SDS-Max shank bit

 18 (11/16")

No load speed

Rotations per minute : rpm=min-

1

Blows per minute : bpm=min-

1

Bit type

Diameter of shank : mm (")

Drilling capacities
: mm (")

Net weight : Kg (lbs)

Cord length : m (ft)

7.8 (17.2)

Standard spec.  : 5 (16.4)
European spec. : 4 (13.1)

STANDARD EQUIPMENT

45 (1-3/4")

Tungusten-carbide
tipped bit

Core bit

125 (4-7/8")

Grip 36 Assembly
(Bar style side handle) ------------ 1pc.

Depth Gauge ----------------------- 1pc.
Grease Vessel (Bit Grease) ------- 1pc.
Plastic Carrying Case ------------- 1pc.
Side Handle Assembly
(D-shaped side handle) ----------- 1pc.

OPTIONAL  ACCESSORIES

The standard equipment for the machine may differ from country to country. 

See next page for detailed information.

L

W

H

Содержание HR4500C

















Отзывы: