Makita GA7050R Скачать руководство пользователя страница 5

Страница: 5 / 16

Maintain a firm grip on the power tool and

position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.

The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b)

Never place your hand near the rotating

accessory.

Accessory may kickback over your hand.

Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
d)

Use special care when working corners,

sharp edges etc. Avoid bouncing and snagging
the accessory.

Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e)

Do not attach a saw chain woodcarving

blade or toothed saw blade.

Such blades create

frequent kickback and loss of control.

Safety Warnings Specific for Grinding and Abrasive
Cutting-Off Operations:

Use only wheel types that are recommended

for your power tool and the specific guard
designed for the selected wheel.

Wheels for

which the power tool was not designed cannot be
adequately guarded and are unsafe.
b)

The grinding surface of centre depressed

wheels must be mounted below the plane of
the guard lip.

An improperly mounted wheel that

projects through the plane of the guard lip cannot
be adequately protected.
c)

The guard must be securely attached to the

power tool and positioned for maximum safety,
so the least amount of wheel is exposed towards
the operator.

The guard helps to protect the operator

from broken wheel fragments, accidental contact with
wheel and sparks that could ignite clothing.
d)

Wheels must be used only for recommended

applications. For example: do not grind with the
side of cut-off wheel.

Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied
to these wheels may cause them to shatter.
e)

Always use undamaged wheel flanges that

are of correct size and shape for your selected
wheel.

Proper wheel flanges support the wheel

thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
f)

Do not use worn down wheels from larger

power tools.

Wheel intended for larger power tool

is not suitable for the higher speed of a smaller tool
and may burst.

Additional Safety Warnings Specific for Abrasive
Cutting-Off Operations:

Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to make an
excessive depth of cut.

Overstressing the wheel

increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
of kickback or wheel breakage.
b)

Do not position your body in line with and

behind the rotating wheel.

When the wheel, at

the point of operation, is moving away from your
body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c)

When wheel is binding or when interrupting a

cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur.

Investigate and take corrective action to

eliminate the cause of wheel binding
d)

Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and
carefully re-enter the cut.

The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.
e)

Support panels or any oversized workpiece

to minimize the risk of wheel pinching and
kickback.

Large workpieces tend to sag under

their own weight. Supports must be placed under
the workpiece near the line of cut and near the
edge of the workpiece on both sides of the wheel.
f)

Use extra caution when making a “pocket

cut” into existing walls or other blind areas.