Makita G12010R Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 44

background image

REPAIR AND REPLACEMENT OF EMISSION-RELATED PARTS

It is recommended that only engine replacement parts which have been authorized and
approved by MAKITA should be used in the performance of any warranty maintenance or repairs
of emission-related parts. These replacement parts will be provided at no charge if the part is still
under warranty.

HOW TO FILE A WARRANTY CLAIM

AND WHERE TO GET WARRANTY SERVICES

Contact the nearest Makita Factory Service Center Manager to determine the appropriate
location where the required warranty services are to be performed. A list of the Factory Service
Center locations and phone numbers are provided below for your convenience.

41850 Christy Street
Fremont, CA 94538-5107
(510)657-9881

1421 N. Clovis Ave., Ste. 112
Fresno, CA 93727
(209)252-5166

14930 Northam Street
La Mirada, CA 90638-5753
(714)522-8088

1970 Fulton Avenue
Sacramento, CA 95825
(916)482-5197

1440 South "E" Street
San Bernardino, CA 92408
(909)885-1289

7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(619)278-4471

1714 E. McFadden Ave., Unit M
Santa Ana, CA 92705
(714)667-5066

333 Littlefield Ave.
South San Francisco, CA 94080
(415)875-1002

16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440

G12010R排対̲GU2000 05.1.20 1:38 PM ページ07

«
...
6
7
8
9
10
...
»

Содержание G12010R













































Отзывы:

Нет отзывов

Похожие инструкции для G12010R

blueplanet 3.0 TL3 M2 WM OD IIG0

Бренд: Kaco Страницы: 262

Бренд: OCULUS Страницы: 28

Бренд: APS Страницы: 70

Бренд: Sigineer Power Страницы: 39

HD67D36-B2-868MHz

Бренд: ADF Web Страницы: 31

Бренд: Hamron Страницы: 28

Pro Enigma MI-X450

Бренд: Aiwa Страницы: 13

Бренд: Parker Страницы: 172

Бренд: Xantrex Страницы: 36

Бренд: TRUlink Страницы: 15

SCSI Differential Converter

Бренд: Black Box Страницы: 3

Бренд: IMO Страницы: 16

Бренд: Metrodata Страницы: 17

SUNNY BOY STORAGE 2.5

Бренд: SMA Страницы: 110

Бренд: Satel Страницы: 4

Бренд: Avenview Страницы: 8

Бренд: HRT Страницы: 4

Бренд: Alinco Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды