background image

PRODUCT

C

ONCEPT AND MAIN APPLICATIONS

P  1/ 1

0

S

pecification

S

tandard equipment

Note:

 The standard equipment for the tool shown above may vary by country.

Model No.

EW1050H

 Description

Engine Pump

Model EW1050H is 24.5cc 4-stroke engine pump to comply with 

all major exhaust emission regulations in the world.

It features the same pumping capacity as the predecessor EW120R,

but it is more cost effective than EW120R.

This product is also available with nozzle and 8m delivery hose 

as Model EW1050HX.

O

ptional accessories

Suction hose .......................... 1

Socket wrench ....................... 1

Hose coupling 

 

....................... 2 (for some countries only)  

Rapid type hose coupling ...... 2 (for some countries only)  

1 inch NPT adapter ............... 1 (for Canada, Mexico, Colombia, Chile, Peru and Brazil only)

Hose band 

 

............................. 3

Strainer  ................................. 1

Delivery hose (8m) 

 

............... 1 (for EW1050HX only)

Nozzle ................................... 1 (for EW1050HX only)

Rapid type Hose coupling set

Coupling for water supply hose (with Hose band)

8m Delivery hose (with Nozzle)

1 inch NPT adapter

Straight unleaded gasoline

*

2

Carburetor

Engine

Displacement: cm³ (cu.in.)
Fuel

Specifications

Model

Type

Net weight

*

3

: kg (lbs)

*2

 Brazil: 25E gasoline

*3

 Dry weight, without suction hose

EW1050H

In compliance with exhaust emission regulations: 

CARB Tier 3, EPA Phase 2, EU Stage 2

Starting system

Max. suction head: m (ft)

Max. output: kW (PS)

Diaphragm

Suction & discharge diameter: mm (")

25.4 (1)

24.5 (1.5)

4-stroke

8.0 (26)

Max. pumping capacity: L/min (US oz/min)

110 (3,700)

Primer pump

Yes

Yes

5.8 (12.8)

0.71 (1.0) [at 7,000 min.

ˉ

¹]

1.0 [at 5,500 min.

ˉ

¹]

Max. torque: N·m

Speed at no load: min.

ˉ

¹ = rpm

7,000

Recoil starter, with mechanical decompression

Max. total head: m (ft)

35 (115)

Fuel tank capacity: L (US oz)
Engine oil

0.5 (16.9)

SAE10W-30 oil

in the class SF or higher of API Classification

231 (9-1/8)

Dimensions

*

1

: mm (")

Width (W)
Height (H)

Length (L)

327 (12-7/8)

319 (12-1/2)

*1

 without suction hose

T

ECHNICAL INFORMATION

L

H

W

Содержание EW1050H











Отзывы: