background image

3

SAFETY INSTRUCTIONS

General Instructions

– To ensure correct operation, user has to read this instruction manual to make

himself familiar with the handling of the Brush Cutter/Grass trimmer.  Users
insufficiently informed will risk danger to themselves as well as others due to
improper handling.

– It is recommended only to lend the Brush Cutter/Grass trimmer to people who

have proven to be experienced with Brush Cutter/Grass trimmers.
Always hand over the instruction manual.

– First users should ask the dealer for basic instructions to familiarize oneself

with the handling of an engine powered cutter.

– Children and young persons aged under 18 years must not be allowed to

operate the Brush Cutter/Grass trimmer.  Persons over the age of 16 years
may however use the device for the purpose of being trained only whilst
under supervision of a qualified trainer.

– Use Brush Cutter/Grass trimmers with the utmost care and attention.
– Operate the Brush Cutter/Grass trimmer only if you are in good physical

condition.  Perform all work calmly and carefully.  The user has to accept
liability for others.

– Never use the Brush Cutter/Grass trimmer after consumption of alcohol or

drugs, or if feeling tired or ill.

Intended use of the machine

– The Brush Cutter/Grass trimmer is only intended for cutter grass, weeds,

Bushes, undergrowth it should not be used for any other purpose such as
Edging or hedge cutting as this may cause injury.

Personal protective equipment

– The clothing worn should be functional and appropriate, i.e. it should be tight-

fitting but not cause hindrance.  Do not wear either jewelry or clothing which
could become entangled with bushes or shrubs.

– In order to avoid either head-, eye-, hand-or foot injuries as well as to protect

your hearing the following protective equipment and protective clothing must
be used during operation of the Brush Cutter/Grass trimmer.

– Always wear a helmet where there is a risk of falling objects.  The protective

helmet (1) is to be checked at regular intervals for damage and is to be
replaced at the latest after 5 years.  Use only approved protective helmets.

– The visor (2) of the helmet (or alternatively goggles) protects the face from

flying debris and stones.  During operation of the Brush Cutter/Grass trimmer
always wear goggles, or a visor to prevent eye injuries.

– Wear adequate noise protection equipment to avoid hearing impairment (ear

muffs (3), ear plugs etc.).

– The work overalls (4) protect against flying stones and debris.

We strongly recommend that the user wears work overalls.

– Special gloves (5) made of thick leather are part of the prescribed equipment

and must always be worn during operation of the Brush Cutter/Grass trimmer.

– When using the Brush Cutter/Grass trimmer, always wear sturdy shoes (6)

with a non-slip sole.  This protects against injuries and ensures a good
footing.

Starting up the brush cutter

– Please make sure that there are no children or other people within a working

range of 15 meters (49ft), also pay attention to any animals in the working
vicinity.

– Before use always check that the Brush Cutter/Grass trimmer is safe for

operation:
Check the security of the cutting tool, the control lever for easy action and
check for proper functioning of the control lever lock.

– Rotation of the cutting tool during idling speed is not allowed.  Check with

your dealer for adjustment if in doubt.  Check for clean and dry handles and
test the function of the start/stop switch.

15 Meter

Diagrammatic figure

Содержание EBH250U

























Отзывы: