![background image](http://html1.mh-extra.com/html/makita/dux18z/dux18z_instruction-manual_3943509012.webp)
12 ENGLISH
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely dis
-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2.
Never recharge a fully charged battery car
-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge with room tem
-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
When not using the battery cartridge, remove
it from the tool or the charger.
5.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
PARTS DESCRIPTION
►
Fig.4
1
Battery cartridge
2
Lock-off lever
3
Switch trigger
4
Hanger
5
Handle
6
Release button
7
Barrier
8
Indicator lamps
9
Main power button
10
Shoulder harness
-
-
-
-
FUNCTIONAL
DESCRIPTION
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Failure to switch off and remove the battery cartridge
may result in serious personal injury from accidental
start-up.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car
-
tridge firmly when installing or removing battery
cartridge.
Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
►
Fig.5:
1.
Red indicator
2.
Button
3.
Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen.
If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly.
If the cartridge does not slide in easily, it is
not being inserted correctly.
Tool / battery protection system
The tool is equipped with a tool/battery protection system.
This system automatically cuts off power to the motor to
extend tool and battery life. The tool will automatically stop
during operation and the indicator lamps light up if the tool
is placed under one of the following conditions:
►
Fig.6:
1.
Indicator lamps
Indicator lamps
Protection
status
Color
Lighted
Off
Blinking
Green
Overload
Red
Overheat
Red
Over-
discharge
Overload protection
If the tool or battery gets into one of the following situa
-
tion, the tool automatically stops and the indicator lamp
starts blinking in green:
— The tool or battery is overloaded by entangled
weeds or other debris.
— The tool is locked.
— The main power button is turned on while the
switch trigger is being pulled.
In this situation, release the switch trigger and remove
the cause of overload if necessary. After that, pull the
switch trigger again to resume.
CAUTION:
Before you remove the cause of
overload, be sure to turn the tool off.
Содержание DUX18Z
Страница 2: ...Fig 1 Fig 2 12 1 2 3 4 5 11 10 9 8 Fig 3 2 1 8 3 4 7 10 5 6 8 9 Fig 4 2 ...
Страница 3: ...2 1 3 Fig 5 1 Fig 6 1 2 Fig 7 1 2 Fig 8 2 1 Fig 9 1 2 Fig 10 3 2 1 1 5 4 Fig 11 1 2 Fig 12 3 ...
Страница 4: ...1 Fig 13 1 2 3 Fig 14 1 Fig 15 Fig 12 3 1 2 Fig 16 1 2 Fig 17 Fig 18 1 2 Fig 19 Fig 20 4 ...
Страница 5: ...1 Fig 21 1 2 Fig 22 1 Fig 23 5 ...