7
ENGLISH
4.
Switch on the motor only when hands and feet
are away from the cutting tool.
5.
Before starting make sure that the cutting tool has no
contact with hard objects such as branches, stones
etc. as the cutting tool will revolve when starting.
6.
Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Method of operation
1.
Never operate the machine with damaged
guards or without the guards in place.
2.
Only use the tool in good light and visibility.
During the winter season beware of slippery
or wet areas, ice and snow (risk of slipping).
Always ensure a safe footing.
3.
Take care against injury to feet and hands from
the cutting tool.
4.
Keep hands and feet away from the cutting
means at all times and especially when switch-
ing on the motor.
5.
Never cut above waist height.
6.
Never stand on a ladder and run the tool.
7.
Never work on unstable surfaces.
8.
Don't overreach. Keep proper footing and
balance at all times.
9.
Remove sand, stones, nails etc. found within
the working range. Foreign particles may
damage the cutting tool and can cause to be
thrown away, resulting in a serious injury.
10.
Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
11.
Before commencing cutting, the cutting tool
must have reached full working speed.
12.
During operation always hold the tool with
both hands. Never hold the tool with one hand
during use. Always ensure a safe footing.
13.
All protective equipment such as guards supplied
with the tool must be used during operation.
14.
Except in case of emergency, never drop
or cast the tool to the ground or this may
severely damage the tool.
15.
Never drag the tool on the ground when mov-
ing from place to place, the tool may become
damaged if moved in this manner.
16.
Always remove the battery cartridge from the tool:
—
whenever leaving the tool unattended;
—
before clearing a blockage;
—
before checking, cleaning or working on
the tool;
—
before making any adjustments, chang-
ing accessories or storing;
—
whenever the tool starts vibrating
unusually;
—
whenever transporting the tool.
17.
Don't force the tool. It will do the job better and
with less likelihood of a risk of injury at the
rate for which it was designed.
18.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks
which may ignite the dust or fumes.
19.
Take a rest to prevent loss of control caused
by fatigue.
We recommend to take a 10 to
20-minute rest every hour.
20.
Do not use the tool on steep slopes.
21.
The shoulder harness must be used during
operation, if supplied with the tool.
Maintenance instructions
1.
The condition of the cutting tool, protec-
tive devices and shoulder harness must be
checked before commencing work.
2.
Turn off the motor and remove the battery cartridge
before carrying out maintenance, replacing the
cutting tool and cleaning the tool.
3.
After use, disconnect the battery cartridge
from the tool and check for damage.
4.
Check for loose fasteners and damaged parts
such as nearly halfway cut-off state in the
cutting tool.
5.
When not in use store the equipment in a dry loca-
tion that is locked up or out of children's reach.
6.
Use only the manufacturer's recommended
replacement parts and accessories.
7.
Always ensure that ventilation openings are
kept clear of debris.
8.
Inspect and maintain the tool regularly, espe-
cially before/after use. Have the tool repaired
only by our authorized service center.
9.
Keep handles dry, clean and free from oil and
grease.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1.
Before using battery cartridge, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
2.
Do not disassemble or tamper with the battery
cartridge.
It may result in a fire, excessive heat,
or explosion.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any con-
ductive material.
(2)
Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.