15 ENGLISH
Power switch action
WARNING:
For your safety, this tool is
equipped with lever which prevents the tool from
unintended starting. NEVER use the tool if it runs
when you simply pull the switch trigger without
pressing the lever. Return the tool to our autho-
rized service center for proper repairs BEFORE
further usage.
WARNING:
NEVER tape down or defeat pur-
pose and function of lever.
WARNING:
Before installing the battery
cartridge on the tool, always check to see that
the switch trigger and lever actuate properly
and return to the "OFF" position when released.
Operating a tool with a switch that does not actuate
properly can lead to loss of control and serious per
-
sonal injury.
CAUTION:
Never put your finger on the
switch when carrying.
The tool may start uninten
-
tionally and cause injury.
NOTICE:
Do not pull the switch trigger hard
without pressing the lever. This can cause switch
breakage.
Press the main power button to turn on the tool. The
power lamp lights up when the tool is turned on. To turn
off the tool, press and hold the main power button. The
power lamp goes off when the tool is turned off.
►
Fig.4:
1.
Power lamp
2.
Main power button
NOTE:
The tool is automatically turned off if the tool is
not operated for a certain period.
To prevent the switch trigger from being accidentally
pulled, a lever is provided. To start the tool, pull the
switch trigger while pressing the lever. Release the
switch trigger to stop.
►
Fig.5:
1.
Lever
2.
Switch trigger
Speed adjusting
You can adjust the tool speed by pressing the main
power button. Each time you press the main power
button, the level of speed changes.
►
Fig.6:
1.
Speed indicator
2.
Main power button
Indicator
Mode
Stroke speed
High
4,400 min
-1
Medium
3,600 min
-1
Low
2,000 min
-1
Reverse button for debris removal
WARNING:
If the entangled branches or
debris cannot be removed by the reverse func-
tion, switch off the tool and remove the bat
-
tery cartridge, and then remove the entangled
branches or debris using tools such as pliers.
Failure to switch off the tool and remove the bat
-
tery cartridge may result in serious personal injury
from accidental start-up. Removing the entangled
branches or debris by hand may cause an injury,
since the shear blades may move in reaction to
removing them.
This tool has a reverse button to change the direction
of shear blades movement. It is only for removing
branches and debris entangled in the tool.
To reverse the shear blades movement, press the reverse
button when the shear blades have stopped, and then pull the
switch trigger while pressing the lever. The power lamp starts
blinking, and the shear blades move in reverse direction.
When entangled branches and debris are removed,
the tool returns to the regular movement and the power
lamp stops blinking and lights up.
►
Fig.7:
1.
Power lamp
2.
Reverse button
NOTE:
If the entangled branches or debris cannot be
removed, release the switch trigger, then press the
reverse button, and then pull the switch trigger until
they are removed.
NOTE:
If you tap the reverse button while the shear
blades are still moving, the tool comes to stop and to
be ready for reverse movement.
Adjusting the cutting angle
CAUTION:
Always be sure that the tool is
switched off before folding or unfolding the head.
CAUTION:
When folding the head for carrying
the tool or after using the tool, be sure to attach
the blade cover before folding the head.
CAUTION:
When folding the head, be careful
not to pinch your fingers between the head and
the slide sleeve.
For DUN500W
The angle of the head can be adjusted in 6 steps. To
change the angle of the head, follow the steps below.
1.
Hold the head and the slide sleeve as shown in the figure.
►
Fig.8:
1.
Head
2.
Slide sleeve
2.
Move the head while holding down the slide
sleeve, and then release the slide sleeve.
3.
Move the head slightly until it is locked with a click.
NOTE:
Make sure that the head is securely locked
before operating the tool.
Hex wrench storage
For DUN600L
When not in use, store the hex wrench as illustrated to
keep it from being lost.
►
Fig.9:
1.
Handle
2.
Hex wrench
Содержание DUN600L
