11 ENGLISH
13.
Before starting work, check that the chain
saw is in proper working order and that its
condition complies with the safety regulations.
Check in particular that:
•
The chain brake is working properly;
•
The run-down brake is working properly;
•
The bar and the sprocket cover are fitted
correctly;
•
The chain has been sharpened and ten-
sioned in accordance with the regulations.
14.
Do not start the chain saw with the chain cover
being installed on it.
Starting the chain saw with
the chain cover being installed on it may cause
the chain cover to thrown out forward resulting in
personal injury and damage to objects around the
operator.
Top handle chainsaw specific safety
warnings
1.
This chain saw is designed especially for tree
care and surgery. The chain saw is intended
to be used by properly trained persons only.
Observe all instructions, procedures and rec
-
ommendations from the relevant professional
organization. Otherwise fatal accidents may
occur. It is recommend that always using a
rising platform (cherry picker, lift) for sawing
in trees. Rappelling techniques are extremely
dangerous and require special training. The
operators must be trained to become familiar
with safety equipment usage and climbing
techniques. Always use the appropriate belts,
ropes and carabiners when working in trees.
Always use restraining equipment for both the
operator and the saw.
2.
Perform cleaning and maintenance before
storage in accordance with the instruction
manual.
3.
Ensure safe positioning of the chain saw
during car transportation to avoid fuel or chain
oil leakage, damage to the tool and personal
injury.
4.
Regularly check the functionality of chain
brake.
5.
Do not fill the chain oil near fire. Never smoke
when you fill the chain oil.
6.
National regulation may restrict the use of the
chain saw.
7.
If the equipment gets heavy impact or fall,
check the condition before continuing work.
Check the controls and safety devices for mal
-
function. If there is any damage or doubt, ask
our authorized service center for the inspec
-
tion and repair.
8.
Always activate the chain brake before starting
the chain saw.
9.
Hold the saw firmly in place to avoid skating
(skid movement) or bouncing of the saw when
starting a cut.
10.
At the end of the cut, be careful to keep your
balance due to the “drop”.
11.
Take into account the direction and speed of
the wind. Avoid sawdust and chain oil mist.
Protective equipment
1.
In order to avoid head, eye, hand or foot
injuries as well as to protect your hearing the
following protective equipment must be used
during operation of the chain saw:
— The kind of clothing should be appropriate, i. e.
it should be tight-fitting but not be a hindrance.
Do not wear jewelry or clothing which could
become entangled with bushes or shrubs. If
you have long hair, always wear a hairnet!
— It is necessary to wear a protective helmet
whenever working with the chain saw. The
protective helmet
is to be checked in regu-
lar intervals for damage and is to be replaced
after 5 years at the latest. Use only approved
protective helmets.
— The
face shield
of the protective helmet (or
the goggles) protects against sawdust and
wood chips. During operation of the chain
saw always wear a goggle or a face shield to
prevent eye injuries.
— Wear adequate
noise protection equip
-
ment
(ear muffs, ear plugs, etc.)
— The
protective jacket
consists of 22 layers
of nylon and protects the operator against
cuts. It is always to be worn when working
from elevated platforms (cherry pickers,
lifts), from platforms mounted on ladders or
when climbing with ropes.
— The
protective brace and bib overall
is
made of a nylon fabric with 22 layers and
protects against cuts. We strongly recom-
mend its use.
—
Protective gloves
made of thick leather are part
of the prescribed equipment and must always be
worn during operation of the chain saw.
— During operation of the chain saw
safety
shoes
or
safety boots
fitted with anti skid
sole, steel toe caps and protection for the
leg must always to be worn. Safety shoes
equipped with a protective layer provide
protection against cuts and ensure a secure
footing. For working in trees the safety boots
must be suitable for climbing techniques.
Vibration
1.
Individuals with poor circulation who are exposed
to excessive vibration may experience injury to
blood vessels or the nervous system. Vibration
may cause the following symptoms to occur in the
fingers, hands or wrists: “Falling asleep” (numb
-
ness), tingling, pain, stabbing sensation, alteration
of skin colour or of the skin.
If any of these symp
-
toms occur, see a physician!
To reduce the risk
of “white finger disease”, keep your hands warm
during operation and well maintain the equipment
and accessories.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Содержание DUC254
