![background image](http://html1.mh-extra.com/html/makita/dtwa260/dtwa260_instruction-manual_4296107011.webp)
11 ENGLISH
Measuring example:
If you configure the following setting, you can read the tool status.
Case 1
Setting item
Tool setting
Measured result
Diagnosis
Torque level
23
20
The tool has stopped by the
setting of the longest workable
time range (3.5 sec.) before
it reaches the setting of the
Tightening Auto Stop mode
(torque level 23).
Workable time range
shortest: 2.5 sec.
longest: 3.5 sec.
3.5
Case 2
Setting item
Tool setting
Measured result
Diagnosis
Torque level
23
23
The tool has stopped by the
Tightening Auto Stop mode
(torque level 23) before it
reaches the setting of longest
workable time range (3.5 sec.).
Workable time range
shortest: 2.5 sec.
longest: 3.5 sec.
3.0
LED indicator / beeper
►
Fig.12:
1.
LED indicator
LED indicator / beeper on the tool shows the following functions.
Alarm No.
Function
Status of the tool
Status of the LED indicator/beeper
Action to be taken
LED indicator
Beeper
E0
Battery installation
error
If the battery car
-
tridge is installed
with the switch
trigger pulled, the
tool stops to avoid
unintentional start.
Blinks in red and
green alternatively.
A series of short
beeps
Install the battery
cartridge with
the switch trigger
released.
E1
Auto-stop with
battery signal
The battery power
became low and it is
time to replace the
battery cartridge.
Blinks in red and
green alternatively.
A series of short
beeps
Replace the battery
with fully charged
one.
E2
Anti-reset of
controller
The battery voltage
dropped abnor-
mally for some
reason, and the tool
stopped.
Blinks in red and
green alternatively.
A series of short
beeps
Replace the battery
with fully charged
one.
E3
Auto-stop with low
remaining battery
capacity
The battery power is
almost used up and
the tool stopped.
Lights up in red.
A long beep
Replace the battery
with fully charged
one.
E4
Overload protection The tool was over-
loaded and stopped.
Blinks in red and
green alternatively.
A series of short
beeps
Remove the cause
of overload, and
then restart the tool.
Ask your local
Makita Service
Center for repair.
E5
Overheat protection Tool's controller
heated up abnor-
mally and the tool
stopped.
Blinks in red quickly.
A series of short
beeps
Remove the battery
cartridge immedi-
ately and cool the
tool down.
E6
Motor lock
The motor has been
locked. At this time,
the tool does not
work.
Blinks in red and
green alternatively.
A series of short
beeps
Ask your local
Makita Service
Center for repair.
E7
Motor failure
The tool detected a
motor failure. At this
time, tool does not
work.
Blinks in red and
green alternatively.
A series of short
beeps
Ask your local
Makita Service
Center for repair.
E8
Switch failure
The tool detected a
switch failure.
Blinks in red and
green alternatively.
A series of short
beeps
Ask your local
Makita Service
Center for repair.
Содержание DTWA260
Страница 2: ...2 2 1 3 Fig 1 1 2 Fig 2 1 Fig 3 1 Fig 4 1 B A Fig 5 3 2 1 Fig 6 2 1 Fig 7 Fig 8 ...
Страница 3: ...3 Fig 9 Fig 10 Fig 11 1 Fig 12 1 2 3 4 Fig 13 1 2 3 Fig 14 1 2 4 3 Fig 15 2 2 1 Fig 16 ...
Страница 4: ...4 Fig 17 ...
Страница 107: ...107 ...