![background image](http://html.mh-extra.com/html/makita/dtw284/dtw284_instruction-manual_230517007.webp)
7 ENGLISH
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►
Fig.2:
1.
Indicator lamps
2.
Check button
Press the check button on the battery cartridge to indi
-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE:
The first (far left) indicator lamp will blink when
the battery protection system works.
Indicating the remaining battery
capacity
Country specific
►
Fig.3:
1.
Battery indicator
When you pull the switch trigger, the LED display shows
the remaining battery capacity. The remaining battery
capacity is shown as the following table.
Battery indicator status
Remaining battery
capacity
On
Off
50% to 100%
20% to 50%
0% to 20%
NOTE:
When the LED display goes off, the tool is
turned off to save the battery power. To check the
remaining battery capacity, slightly pull the switch
trigger.
NOTE:
The LED display goes off approximately one
minute after releasing the switch trigger.
NOTE:
When the LED display lights up and the tool
stops even with a recharged battery cartridge, cool
down the tool fully. If the status will not change, stop
using and have the tool repaired by a Makita local
service center.
NOTE:
When the tool is overheated, the light flashes
for one minute, and then the LED display goes off. In
this case, cool down the tool before operating again.
Switch action
►
Fig.4:
1.
Switch trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
NOTE:
The tool automatically stops when you keep
pulling the switch trigger for 3 minutes.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
►
Fig.5:
1.
Lamp
►
Fig.6:
1.
Button
To turn on the lamp status, press the button
for
one second. To turn off the lamp status, press the but
-
ton
for one second again.
With the lamp status ON, pull the switch trigger to turn
on the lamp. To turn off, release it. The lamp goes out
approximately 10 seconds after releasing the switch
trigger.
With the lamp status OFF, the lamp does not turn on
even if pulling the trigger.
NOTE:
To confirm the lamp status, pull the trigger.
When the lamp lights up by pulling the switch trigger,
the lamp status is ON. When the lamp does not come
on, the lamp status is OFF.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:
While pulling the switch trigger, the lamp
status cannot be changed.
NOTE:
For approximately 10 seconds after releasing
the switch trigger, the lamp status can be changed.
Содержание DTW284
Страница 2: ...2 1 2 3 Fig 1 1 2 Fig 2 1 Fig 3 1 Fig 4 1 Fig 5 1 Fig 6 1 A B Fig 7 1 2 3 4 5 6 Fig 8 ...
Страница 3: ...3 1 3 2 Fig 9 1 2 3 Fig 10 1 4 3 2 Fig 11 2 3 1 Fig 12 1 Fig 13 Fig 14 ...
Страница 90: ...90 ...
Страница 91: ...91 ...