![background image](http://html1.mh-extra.com/html/makita/dtm51zjx2/dtm51zjx2_instruction-manual_3977115008.webp)
8
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
Installing or removing application tool (optional
accessory) (Fig. 7, 8, 9 & 10)
WARNING:
• Do not install application tool upside down. Installing
application tool upside down may damage the tool and
cause serious personal injury.
• Install attachment tool in the correct direction according
to your work. Application tool can be installed at an
angle of every 30 degree.
CAUTION:
• Be careful when closing the lock lever. The lock lever
may close suddenly and pinch your finger.
• Clean up dust and perform lubrication on the moving
part of the lock lever from time to time.
Otherwise dust may accumulate in the moving part of
the lock lever and hinder its smooth movement.
• Do not start the tool while the lever opens. The tool
may be damaged.
1.
Open the lock lever fully. And remove the holder
bolt.
2.
Put an application tool (optional accessory) on the
tool flange so that the protrusions of the tool flange
fit in the holes in the application tool.
3.
Insert the holder bolt till it stops. And then, return the
lock lever to its original position.
When using sanding application tool, mount the applica-
tion tool on the sanding pad so that it matches the sand-
ing pad direction.
The sanding pad has a hook and loop type fitting system
which allows easy and rapid fitting of a sanding paper.
As sanding papers have holes for dust extraction, mount
a sanding paper so that the holes in a sanding paper
match those in the sanding pad.
To remove a sanding paper, raise its end and peel it off.
To remove the holder bolt, follow the installation proce-
dures in reverse.
When using application tools with a different type of
installation section, use a correct adapter (optional
accessory).
OPERATION
WARNING:
• Before starting the tool and during operation, keep your
hand and face away from the application tool.
CAUTION:
• Do not apply excessive load to the tool which may
cause a motor lock and stop the tool.
Cutting, sawing and scraping (Fig. 11)
CAUTION:
• Do not move on the tool forcibly in the direction (eg.
towards either side) of tool application with no cutting
edge. It may damage the tool.
Put the application tool on the workpiece.
And then move the tool forward so that the application
tool movement does not slow down.
NOTE:
• Forcing or excessive pressure on the tool may reduce
efficiency.
• Before cutting operation, it is recommended to preset
the orbital stroke rate 4 – 6.
• Remove sawdust by drawing the tool adequately. It
increases work efficiency.
• The round saw is recommended for cutting long
straight line.
Sanding (Fig. 12)
CAUTION:
• Do not reuse a sanding paper used for sanding metal
to sand wood.
• Do not use a worn sanding paper or sanding paper
without grit.
Apply a sanding paper on the workpiece.
NOTE:
• Using a test material sample to try is recommendable
to determine a correct orbital stroke rate suitable for
your work.
• Use a sanding paper with the same grit until sanding
the whole workpiece is completed. Replacing a sand-
ing paper with different grit sanding paper may not get
a fine finish.
Dust extraction attachment (optional accessory)
(Fig. 13 & 14)
• Install dust nozzles and dust attachment.
• Install the nozzle band on the tool so that its protru-
sions fit in the holes in the tool to secure it.
• Put the felt ring and the sanding pad on the dust attach-
ment and then secure them with the application tool
installation bolt.
When you wish to perform cleaner operation, connect a
vacuum cleaner to your tool. Connect a hose of vacuum
cleaner to the dust extraction attachment (optional
accessory).
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Segment saw blade
• Round saw blade
• Plunge cut saw blade
Содержание DTM51ZJX2
